Canon Ir 1600 User Guide

7-9Finisher-L1
Handling Options
7
NOTE
•Copies are stapled in the following places:
- When an original is placed on the platen glass:
- When originals are placed in the feeder:
•If the number of sheets in one set exceeds 15 stapling will not be performed. Only collating will be performed.•If the machine stops during stapling and  is displayed, it means that almost all of the staples have 
been used up and the staple case must be replaced. To proceed, replace the staple case. (See “Replacing the Staple...

Handling Options
7
7-10Finisher-L1
Clearing Paper Jams in the Finisher-L1
If a paper jam occurs when using the finisher, a screen similar to the one shown below appears on 
the touch panel display. Check where the jam occurred, and follow the procedure described below 
and the procedure that appears on the touch panel display, to remove the jammed paper.
CAUTION
•When removing jammed originals or paper, take care not to cut your hands on the edges of the original or 
paper.
•When removing jammed paper or...

7-11Finisher-L1
Handling Options
7
2If you see the jammed paper, remove it.
If you cannot remove it, go to step 3.
3Open the stack bypass.
4Pull out the left cover.
CAUTION
•Grasp the handle and pull out the left cover horizontally to the left. (Be careful not to pull it upward as it may 
easily come off.)
 

Handling Options
7
7-12Finisher-L1
5Open the upper left cover.
6If you see any jammed paper, remove it.
If you cannot remove it, go to step 7.
CAUTION
•Be careful not to touch inside the machine because some parts get very hot.
7Holding the green knob, lift the inner guide.
 

7-13Finisher-L1
Handling Options
7
8Remove any jammed paper under the inner guide.
CAUTION
•Be careful not to touch inside the machine because some parts get very hot.
9Close the upper left cover.
CAUTION
•When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
 

Handling Options
7
7-14Finisher-L1
10Close the left cover.
CAUTION
•Close the left cover until it latches.
•When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
11Close the stack bypass.
CAUTION
•When closing the stack bypass, be careful not to get your fingers caught, as this may result in personal 
injury.
 

7-15Finisher-L1
Handling Options
7
12Close the front cover.
CAUTION
•When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
 

Handling Options
7
7-16Finisher-L1
Replacing the Staple Cartridge in the Stapler
Unit-K1
When the finisher is almost out of staples and the staple cartridge must be replaced, the following 
display appears. Follow the procedure described below to replace the staple cartridge.
1Open the front cover of the finisher.
2Pull out the staple cartridge, holding the tab as illustrated below.
LOAD STAPLES
Hold here to pull out 
the cartridge.
 

7-17Finisher-L1
Handling Options
7
3Insert the new staple cartridge.
IMPORTANT
•Use only the special staple cartridge intended for use with this machine.
NOTE
•Only one staple cartridge can be inserted at a time.
4Close the front cover of the finisher.
CAUTION
•When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
 

Handling Options
7
7-18Finisher-L1
Removing Jammed Staples from the Stapler Unit-K1
If the machine does not staple even though you have set the staple mode, a staple jam may have 
occurred in the Stapler Unit-K1. Check the staple cartridge and remove jammed staples if 
necessary.
1Open the front cover of the finisher.
2Pull out the staple cartridge, holding the tab as illustrated below.
Hold here to pull out 
the cartridge.