Canon Ir 1600 User Guide

6-21Service Call Message
Troubleshooting
6
2If the problem persists, do the following and contact your local authorized Canon 
dealer.
Turn off the main power.
Unplug the power cord from the wall outlet.
NOTE
•When consulting your local authorized Canon dealer, check the following:
- Model name
- Problem and status of the machine
- Error code on the display
 

Troubleshooting
6
6-22Service Call Message
 

CHAPTER
1-1
1
Before You Start Using This 
Machine
This chapter describes what you should know before using this machine, such as main features, 
parts and their functions, how to turn on the main power, and so on.
About the Installation Location and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Installation Precautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2...

7-2System Configuration
Handling Options
7
System Configuration
The following options can be attached to the machine.
1Feeder (ADF-J1)
2Finisher-L1
3Inner 2-Way Tray-B1
4Card Reader-C1 (Control Card)5Cassette Feeding Module-F1
(For iR1600 only)
6Cassette Feeding Module-G1
(For iR2000 only)
7Cassette Feeding Module-H1
(For iR1600 only)
Main unit
 

7-3Feeder (ADF-J1)
Handling Options
7
Feeder (ADF-J1)
With the optional feeder attached, you can place a stack of originals in the original supply tray, and 
they are automatically fed to the platen glass for copying.
IMPORTANT
•Blocking the paper delivery slot may damage the originals. Do not place objects in the original output area.
Parts and Their Functions
1Feeder cover
2Slide guide3Original supply tray
4Original output area
 

Handling Options
7
7-4Feeder (ADF-J1)
Clearing Paper Jams in the Feeder
If a paper jam occurs in the feeder, the following display appears. Follow the procedure described 
below to remove the jammed paper.
CAUTION
•When removing jammed originals or paper, take care not to cut your hands on the edges of the original or 
paper.
•When removing jammed paper or when inspecting the inside of the machine, do not allow necklaces, 
bracelets, or other metal objects to touch the inside of the machine, as this may...

7-5Feeder (ADF-J1)
Handling Options
7
2Remove any jammed original.
If you cannot remove the original, go to step 3.
IMPORTANT
•Do not pull the original forcefully, because it may tear.
3Turn the green knob and remove any jammed original.
If you cannot remove the original, go to step 4.
4Close the upper cover of the feeder.
 

Handling Options
7
7-6Feeder (ADF-J1)
CAUTION
•When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
5Open the feeder, and remove any jammed original.
6Close the feeder.
CAUTION
•When closing the feeder/platen glass cover, be careful not to get your fingers caught, as this may result in 
personal injury.
 

7-7Finisher-L1
Handling Options
7
Finisher-L1
The Finisher-L1 is equipped with the following functions: Collate, Offset, and Staple modes. (See 
“Finishing Functions,” on p. 7-8.)
Parts and Their Functions
1Front cover
Open this cover to replace the staple case in the 
stapler unit, or when a staple jam occurs. (See 
“Replacing the Staple Cartridge in the Stapler Unit-
K1,” on p. 7-16. “Removing Jammed Staples from 
the Stapler Unit-K1,” on p. 7-18.)2Auxiliary tray
When feeding large-size paper, such as...

Handling Options
7
7-8Finisher-L1
Finishing Functions
The Finisher-L1 is equipped with the following functions:
■Collate Mode
This function automatically collates print sets into page order before they are delivered.
■Staple Mode
This function automatically collates print sets into page order, staples the sets, and outputs 
them.
CAUTION
•Do not place your hand in the output tray while the finisher is attached, as this may result in personal injury.
IMPORTANT
•The output tray moves down when each set of...