Canon Imageprograf Ipf8300 User Guide

Network Setting (Windows)
Configuring the Printer Driver Destination  ...................................................................................................... 963
 
Configuring the Printer's NetWare Network Settings ...................................................................................... 964
Specifying the Printer's Frame Type ............................................................................................................... 965
Specifying NetWare Print...

Configuring the Printer's NetWare Network Settings
Follow the steps below to configure the NetWare network settings.
1. Start  the  web  browser  and  enter  the  following  URL  in  the  Location  (or Address   )  box  to  display  the  RemoteUI
page.
http://printer IP address or name/ Example: http://xxx.xxx.xxx.xxx/
2. Select  Administrator Mode  and click Logon.
3. If a password has been set on the printer, enter the password.
4. Click  Network  in the Device Manager  menu at left to display the...

ItemDetailsDefaultSettingNDS PSer-
verTree NameSpecify the name of an NDS tree that has a NetWare print server. (0–32 characters)—Context NameSpecify the name of a context that has a NetWare print server.
(0–255 characters)—Print Server
NameSpecify the name of a NetWare print server.
(0–64 characters)—Print Server
PasswordSet a password for the print server.
(0–20 characters)—Polling IntervalSpecify the interval to confirm jobs.
(1–255 seconds)5NPrinterPrint Server
NameSpecify the name of a NetWare print...

3.Choose  Protocol Settings  from the Printer menu.
4. Click the  NetWare tab and select the frame type in the  NetWare Frame Type list.Network Setting 
>
 Network Setting (Windows) 
>Specifying the Printer's Frame TypeiPF830010966
 

5.Select  the  IPv4  tab.  In  IP  Address ,  enter  the  IP  address  assigned  to  the  printer,  and  then  enter  the  subnet  mask  in
Subnet Mask  and the default gateway in  Gateway Address.Important•You must specify the IP address here to be able to configure NetWare protocol settings using Remo-
teUI.
6. Click  Set.
7. Click  OK after the  Confirmation  message is displayed.
8. Exit imagePROGRAF Device Setup Utility.
Network Setting 
>
 Network Setting (Windows) 
>iPF8300Specifying the...

Specifying the frame type using the printer Control Panel1. On the  Tab Selection screen  of the Control Panel, press  ◀ or  ▶ to select the Settings/Adj. tab (
).
Note•If the  Tab Selection screen  is not displayed, press the  Menu button.
2.Press the  OK button.
The  Set./Adj. Menu  is displayed.
3. Press  ▲ or  ▼ to select  Interface Setup , and then press the  OK button.
4. Press  ▲ or  ▼ to select  NetWare , and then press the  OK button.
5. Press  ▲ or  ▼ to select  NetWare , and then press the  OK...

Important•Be sure to complete step 11. This will activate the values you have entered.Note•If an error message is displayed, check the settings and correct any invalid values.
• To cancel this process, press the  Back button.
Specifying NetWare Print Services
Before printing in a NetWare network, you must configure print services such as print servers, print queues, and so on. You can configure the print service settings from a computer using any of the following Novell software provided with NetWare....

2.Run Quick Setup.
1. Choose  Print Services Quick Setup  in the Tools menu.
2. Enter  a  desired  name  in  Print  Server  Name.  To  use  an  existing  print  server,  click  the  button  at  right  and
choose the name from the list.
3. Enter a desired printer name in  Name.
4. To use the printer in queue server mode, choose  Other/Unknown in Type . To use the printer in remote printer
mode,  choose  Parallel  in Type ,  click  Communications ,  and  set Ports  to LPT1   and Connection  Type  to
Manual...

Note•The  print  server  name  will  be  required  when  configuring  the  printer's  protocol  settings.  Write  down
the print server name for future reference.
4. Specify the printer type.
1. To  use  the  printer  in  queue  server  mode,  choose  Other/Unknown  in Type .  To  use  remote  printer  mode,  set
Printer Type  to Parallel  and Position  to Manual Load .
2. Press the Esc key.
3. After the confirmation message is displayed, choose  Yes and press the Enter key.
5. Set a password.
1. In...

7.To use burst mode, choose  On for  NCP Burst Mode .Note•Burst mode supports fast data transfer when printing in queue server mode. Normally, choose  On.
8. In Print Application , click the print service to be used.
Note•Only  one  print  service  selected  here  will  be  enabled.  Multiple  print  services  are  not  available  at  the
same time.
9. For packet signature, click  If Requested by Server in Packet Signature .
10. Complete the following settings based on the selected service.
•If you have...