Canon Imageprograf Ipf8300 User Guide

2.If the Carriage Cover is dirty, use a damp cloth that you have wrung out completely to wipe it clean.Important•Do not touch the Linear Scale (a), Carriage Shaft (b), or Fixed Blade (c).
•Never touch the metal contacts of the Carriage. This may damage the printer.
Maintenance 
>
 Printheads 
>iPF8300Replacing the Printhead111003
 

3.If the ventilation duct (a) is dirty, use a damp cloth that you have wrung out completely to wipe it clean.
If the Carriage is obscuring the ventilation duct, move the Carriage manually before cleaning the duct.
4. Pull up the Carriage Cover to open it completely.
Maintenance 
>
 Printheads 
>Replacing the PrintheadiPF8300111004
 

5.Pull the Printhead Fixer Lever forward all the way to open it completely.
6.Pull up the Printhead Fixer Cover to open it completely.
Maintenance 
>
 Printheads 
>iPF8300Replacing the Printhead111005
 

7.Remove the Printhead and press the  OK button.Note•Dispose of the used Printhead in accordance with local regulations.
8. Holding the new Printhead by the grips (a), remove it from the pouch.
Maintenance 
>
 Printheads 
>Replacing the PrintheadiPF8300111006
 

Important•When  handling  the  Printhead,  always  hold  it  by  the  grips  (a).  Never  touch  the  nozzles  (b)  or  metal
contacts (c). This may damage the Printhead and affect printing quality.
• Never touch the ink supply section (d). This may cause printing problems.
•If you need to put a Printhead somewhere temporarily before installation, do not keep the nozzles and
metal  contacts  facing  down.  If  the  nozzles  or  metal  contacts  are  damaged,  it  may  affect  the  printing
quality.
9....

10.With the nozzles facing down and the metal contacts toward the back, tilt the Printhead slightly forward and insert it
into the Carriage. Carefully push the printhead firmly into the Carriage, ensuring that the nozzles and metal contacts
do not touch the carriage.
11. Pull the Printhead Fixer Cover down toward the front to lock the Printhead in place.
Maintenance 
>
 Printheads 
>Replacing the PrintheadiPF8300111008
 

12.Push the Printhead Fixer Lever toward the back of the printer until it clicks.
13.Push the Carriage Cover down toward the front.
Maintenance 
>
 Printheads 
>iPF8300Replacing the Printhead111009
 

14.Close the Top Cover.
Ink now fills the system. It takes about 13 minutes for ink to fill the system.
Important•Never remove an Ink Tank or Maintenance Cartridge while the system is filling with ink.Note•The procedure is now finished if you have set  Rep.P.head Print to Off  in the Control Panel menu.
If so, execute  Head Posi. Adj.  > Auto(Advanced)  in the Control Panel menu.
 (See " Automatic Adjustment to Straighten Lines and Colors (Head Posi. Adj.) .")
→P.839
15.Follow  the  instructions...

Cutter Unit
Cutter Unit ..................................................................................................................................................... 1011
Replacing the Cutter Unit .............................................................................................................................. 1011
Cutter Unit
The printer can use the following Cutter Unit. •Cutter Unit CT-06
Note•For instructions on Cutter Unit replacement,  see "Replacing the Cutter Unit...

5.Open the Top Cover.
6.If the Cutter Unit or Carriage Cover is dirty, use a damp cloth that you have wrung out completely to wipe it clean.
Important•Do not touch the Linear Scale (a), Carriage Shaft (b), or Fixed Blade (c).
Maintenance 
>
 Cutter Unit 
>Replacing the Cutter UnitiPF8300111012