Canon Imageprograf Ipf8300 User Guide

Problems Regarding Paper
Clearing Jammed Roll Paper ......................................................................................................................... 1043
Clearing a Jammed Sheet ............................................................................................................................. 1047
 
Roll paper cannot be inserted into the paper feed slot ..................................................................................1051
Cannot load sheets...

Caution•If you push the Carriage to the left edge, the blade of the Cutter Unit will be lowered in preparation to
cut the paper. Be careful not to pinch your fingers between the Carriage and Platen if you have push-
ed the Carriage to the left edge or if a paper jam occurs during cutting.Important• Do not touch the Linear Scale (a), Carriage Shaft (b), or Fixed Blade (c).
Troubleshooting 
>
 Problems Regarding Paper 
>Clearing Jammed Roll PaperiPF8300121044
 

4.Lift the Release Lever.
5.Holding  the  paper  on  both  sides,  pull  the  jammed  portion  out  toward  the  front.  Use  scissors  or  a  cutting  tool  to  cut
away the printed or wrinkled portion.
Caution• When cutting paper, be careful to avoid injury or damage to the printer.
Troubleshooting 
>
 Problems Regarding Paper 
>iPF8300Clearing Jammed Roll Paper121045
 

6.If the Carriage is on the left, move the Carriage to the right until it stops.Important•Always move the Carriage to the right side. If the Carriage is on the left, a Carriage error may occur
when you turn on the printer.
7. Hold  the  edge  of  the  roll  paper  in  the  middle  as  you  gently  pull  it  evenly  to  the  position  of  the  Ejection  Guide  (a).
Align  the  right  side  of  the  roll  paper  with  the  Paper  Alignment  Line  (b),  keeping  this  side  parallel  to  the  line,  and...

8.Close the Top Cover.
9. Turn the printer on.   (See "Turning the Printer On and Off .")→P.893
The roll is now advanced. After it is finished being advanced, you can resume printing.
Note• To ensure that the edge is cut more neatly, follow these steps to cut it.
1. Press the  Feed button.
2. Hold down the  ▼ button to advance the paper.
3. Press the  Cut button, and then select  Yes to cut the edge.
 (See " Specifying the Cutting Method for Rolls .")
→P.794
Clearing a Jammed Sheet
If a...

3.If the Carriage is out, move the Carriage out of the way, away from the paper.Caution•If you push the Carriage to the left edge, the blade of the Cutter Unit will be lowered in preparation to
cut the paper. Be careful not to pinch your fingers between the Carriage and Platen if you have push-
ed the Carriage to the left edge or if a paper jam occurs during cutting.Important• Do not touch the Linear Scale (a), Carriage Shaft (b), or Fixed Blade (c).
Troubleshooting 
>
 Problems Regarding Paper...

4.Lift the Release Lever.
5.If the paper is visible, hold the paper and pull it out toward the front.
6.If the paper is not visible, lift the Ejection Guide, remove the Roll Holder, and clear the paper jam from below.
Troubleshooting 
>
 Problems Regarding Paper 
>iPF8300Clearing a Jammed Sheet121049
 

After  removing  the  paper,  make  sure  there  are  no  other  scraps  of  paper  in  the  printer,  and  then  lower  the  EjectionGuide.
7. If the Carriage is on the left, move the Carriage to the right until it stops.Important•Always move the Carriage to the right side. If the Carriage is on the left, a Carriage error may occur
when you turn on the printer.
8. Lower the Release Lever and close the Top Cover.
9. Turn the printer on.   (See "Turning the Printer On and Off .")→P.893...

Roll paper cannot be inserted into the paper feed slotCauseCorrective ActionThe roll paper is warped.Straighten out curls and reload the roll.Paper is jammed by the paper feed slot.Remove the jammed paper. (See " Clearing Jammed Roll Paper .")
→P.1043
 (See " Clearing a Jammed Sheet .")
→P.1047
The paper source selection is incorrect.Press the Load button and select the paper source.
Cannot load sheets
CauseCorrective ActionThe paper source selection is incorrect.Press the  Load button...

The media take-up unit continues rotatingCauseCorrective ActionThere is a foreign object in the path of the Media Take-up Sensor (indicated by adotted line).Remove the foreign object from
the Media Take-up Sensor path.
Arrange the Basket Cloth and
Basket Rod so they do not in-
terfere with the Media Take-up
Sensor.The Media Take-up Sensor cord is not connected to the Right Media Take-up Unit
correctly.Reconnect the Media Take-up
Sensor cord as follows.
1. Turn the printer off.
2. Disconnect  the  Media...