Canon Imageprograf Ipf8300 User Guide

The paper is too small.CauseCorrective ActionWhen Detect Mismatch  in the Control Panel
menu is set to  Pause, paper smaller than the
size specified in the printer driver is loaded.Press  ▲ or  ▼ to select  Print, and then press the  OK button to resume
printing.
However, note that this error may cause paper jams and affect the
printing quality.Adjust the paper size setting in the printer driver to match the size loa-
ded in the printer as follows.
1. Press  ▲ or  ▼ to select  Stop Printing , and then...

CauseCorrective ActionThe loaded paper is too small.
(When you have attempted to print a test
print sheet or other printer status informa-
tion.)2. Replace the roll with a roll 10 inches wide or larger.
 (See " Attaching the Roll Holder to Rolls .")
→P.774
 (See " Loading Rolls in the Printer .")
→P.777
The printer will resume printing.
Press  ▲ or  ▼ to select  Stop Printing , and then press the  OK button.
PaprWidth Mismatch
CauseCorrective ActionWhen  Detect Mismatch  in the Control...

CauseCorrective Action (See "Loading Rolls in the Print-
er .")
→P.777
If this error recurs after you reload
the roll, remove the Roll Holder
from the printer, push the roll firmly
in until it touches the Roll Holder
flange, and reload the Roll Holder in
the printer.
 (See " Attaching the Roll Holder to
Rolls .")
→P.774
Follow these steps to reload the
sheet.
1. Lift the Release Lever.
2. Adjust  the  right  edge  of  the  sheet
to make it parallel to the right Pa-
per  Alignment  Line...

CauseCorrective ActionPress ▲ or  ▼ to select
Change Paper , and then press
the  OK  button to stop printing.
Either change the printer driv-
er  Paper Source  setting or re-
place the paper with paper
long enough for the print job,
and then try printing again.
When using the Media Take-
up Unit, press  ▲ or  ▼ to se-
lect  Stop Printing , and then
press the  OK button to stop
printing.
Remove the printed document
from the Media Take-up Unit,
replace the roll with a roll that
has enough paper for the...

CauseCorrective ActionYou have attempted to print on a roll,
but no roll is loaded.Press  ▲ or  ▼ and select  Stop Printing  or press the Stop button to stop
printing.
Roll printing is selected, but sheets are loaded.
CauseCorrective ActionA print job for rolls was received
when a sheet is loaded.Follow these steps to load and print on a roll.
1. Press  ▲  or  ▼  to  select  Eject  Paper ,  press  the OK  button,  and  remove  the
sheet.  (See " Removing Sheets .")
→P.810
2. Load a new roll....

No sheets.CauseCorrective ActionA sheet has come out of the printer during printing.1.Lift the Release Lever and remove the paper.
2. If " Not finished printing. Finish printing re-
maining  jobs? "  is  shown  on  the  Display
Screen, press the  OK button.
Printing  will  resume,  starting  from  the  page on which the error occurred.
Sheet printing is selected.
CauseCorrective ActionYou have attempted to print on a sheet, but
no sheet is loaded.Press  ▲ or  ▼ to select  Load Paper , and then...

Paper loaded askew.CauseCorrective ActionPaper loaded crooked was detected when the paper was advanced.Follow these steps to reload the roll.
1. Lift the Release Lever.
2. Adjust  the  right  edge  of  the  roll  to  make  it
parallel to the orange Paper Alignment Line.
3. Lower the Release Lever.
 (See " Loading Rolls in the Printer .")
→P.777
If this error recurs after you reload the roll, re-
move the Roll Holder from the printer, push the
roll firmly in until it touches the Roll Holder...

Cannot feed paper.CauseCorrective ActionA paper jam oc-
curred in the print-
er during printing.1. Lift the Release Lever and remove the jammed paper.
 (See " Clearing Jammed Roll Paper .")
→P.1043
 (See " Clearing a Jammed Sheet .")
→P.1047
2. Load paper.
3. Lower the Release Lever.
4. If " Not finished printing. Finish printing remaining jobs? " is shown on the Display Screen,
press the  OK button.
Printing will resume, starting from the page on which the error occurred.
 (See...

End of paper feed.CauseCorrective ActionYou are pressing the ▲ button on the Control Panel and trying to rewind the roll to the edge.Release the  ▲ button.Paper can be retracted only up to 17 mm (0.7 in) when using the Media Take-up Unit.Release the  ▲ button.
Rel lever is in wrong position.
CauseCorrective ActionThe Release Lever is up.Lower the Release Lever.If the error occurs again, turn off the printer and wait a while before restoring power.
Rewinding error.
CauseCorrective ActionThere is some...

Turn on the media take-up unit.CauseCorrective ActionThe Media Take-up Unit was off when you selected Enable for Take-up Reel .Turn the Media Take-up Unit on.
Borderless printng not possible.
CauseCorrective ActionThe print job received specifies a
type or width of paper that is not
compatible with borderless print-
ing.Follow these steps to change the settings of the print job to enable borderless print-
ing.
1. Press  ▲ or  ▼ to select  Stop Printing , and then press the  OK button.
2. Make  sure  the...