Canon Imageprograf Ipf8300 User Guide

 (See "Removing Ink Tanks .")→P.1033Important•If  consumables  must  be  replaced,  the  message  " Consumables  must  be  replaced.  Call  for  service. "
is shown on the Display Screen and preparation is not possible. If this message is displayed, press the
OK  button and contact your Canon dealer for assistance.
Remove the Ink Tank
1. Open the left and right ink tank covers.
2.Lift  the  stopper  (a)  of  the  Ink  Tank  Lock  Lever  (a).  Lift  the  Ink  Tank  Lock  Lever  until  it...

3.Hold the Ink Tank by the handle (a) and remove it. Press the  OK button.Note•Store the Ink Tank you removed in the box with the ink holes (a) facing up. Otherwise, ink may leak
and cause stains.
4. Repeat steps 2 and 3 to remove all ink tanks.
Maintenance 
>
 Other Maintenance 
>Preparing to Transfer the PrinteriPF8300111034
 

5.Push down the release lever (a) as shown as you gently return all ink tank lock levers to the original position.
6.Close the Ink Tank Cover.
At this point, ink is drawn out from inside the tubes.
Important•Do not remove the Maintenance Cartridge during this process.
When the process is finished, " Preparations for moving the printer finished. Turn the power off " is displayed.
Maintenance 
>
 Other Maintenance 
>iPF8300Preparing to Transfer the Printer111035
 

Pack the printer1. Press the  Power button and turn off the printer.Important•Turn  off  the  printer  before  you  unplug  it.  It  may  damage  the  printer  if  you  unplug  it  before  it  is  off
and  transfer  it  in  that  state.  If  you  accidentally  unplug  the  printer,  plug  it  in  again,  reinstall  the  ink tanks, and follow this procedure again.
2. Disconnect the power cord, interface cable, and Media Take-up Unit Power Inlet.
3. Open the Top Cover and lift the Ejection Guide.
4.Remove...

5.Grasp the Belt, insert it between the Belt Stopper, and affix the Belt Stopper with a hex screw at the position indica-
ted.Maintenance 
>
 Other Maintenance 
>iPF8300Preparing to Transfer the Printer111037
 

Important•Here,  the  Belt  Stopper  is  the  one  that  was  removed  and  stored  after  initial  installation.  Neglecting  to
attach the Belt Stopper may damage the printer.
• Do not touch the Linear Scale (a), Carriage Shaft (b), or Fixed Blade (c).
6. Close the Top Cover.
7.Tape down printer covers to secure them, in the reverse order of tape removal during installation.
8. If the Output Stacker is installed, reverse the installation procedure to remove the Output Stacker.
9. Remove the Stand by...

10.Disassemble and repackage the Stand by following the installation procedure in reverse.
11. Repack the Roll Holder, Holder Stopper, and printer in shipping materials, and then package them in a shipping box.
Updating the Firmware
Update the printer firmware to take advantage of new and improved printer functions.
Confirming the firmware version
1. On the  Tab Selection screen  of the Control Panel, press  ◀ or  ▶ to select the Settings/Adj. tab (
).
Note•If the  Tab Selection screen  is not displayed,...

Troubleshooting
Frequently Asked Questions1041
Problems Regarding Paper 1043
Printing does not start1054
The printer stops during a print job1056
Problems with the printing quality1057
Cannot print over a network1069
Installation problems1071
Other problems1073
Troubleshooting 
>iPF8300121040
 

Frequently Asked Questions
Frequently Asked Questions ......................................................................................................................... 1041
Frequently Asked Questions
This section presents frequently asked questions and answers. To view more detailed explanations, click the hyperlinks in
the answer column.
QuestionAnswerHow do I print on a
roll?When printing on rolls, after loading the roll, specify the paper type and length, both on the
Control Panel and in the...

QuestionAnswerHow do I print without
wasting all the blank
space on the right side
when printing an A4-
sized original at A3
size?By specifying to rotate originals 90 degrees in the printer driver, you can print at A4 size to
fill the width of A3 paper.
⇒ "Conserving Roll Paper by Rotating Originals 90 Degrees
→P.161 "
How do I print in land-
scape (or portrait) ori-
entation?You can print originals that are in landscape (or portrait) orientation automatically enlarged to fit the roll width. This...