Canon Imageprograf Ipf8300 User Guide

•If no print job was received
1.Press the  Load button.
2.Press  ▲ or  ▼ to select  Cut Sheet , and then press the  OK button.
Note•If any paper has been advanced that will not be used, a message is shown requesting you to remove it.
Press  ▲  or  ▼  to  select  " Yes",  and  then  press  the  OK  button.  Remove  the  paper  and  go  to  the  next
step.
2. Lift the Release Lever and open the Top Cover.
Handling Paper 
>
 Handling sheets 
>iPF8300Loading Sheets in the Printer7803
 

Important•Do not touch the Linear Scale (a), Carriage Shaft (b), or Fixed Blade (c).
3. With  a  sheet  lengthwise  and  printing-side  up,  insert  it  between  the  Platen  (a)  and  the  Paper  Retainer  (b).  Align  the
edges of the sheet as follows.
1. Align the sheet with the Paper Alignment Line (c) at right.
2. Align the inserted edge of the sheet with the leading edge of the Paper Alignment Line (d), as shown.
Handling Paper 
>
 Handling sheets 
>Loading Sheets in the PrinteriPF83007804
 

When inserted, sheets are automatically held by suction against the Platen.
Important•Load  a  sheet  so  that  it  is  parallel  to  the  Paper  Alignment  Line  at  right  (c).  Loading  paper  askew  will
cause an error.
• Warped paper may rub against the Printhead. Straighten paper if it is warped before loading it.Note•You can adjust the strength of suction holding paper against the Platen when the Release Lever is up.
If it is difficult to load paper, press the  ▲ or  ▼ button on the Control Panel...

4.Lower the Release Lever and close the Top Cover.
•
If a print job was received
Pressing the  OK button will advance the paper, and then printing will begin.
•
If no print job was received
A menu for selection of the type of paper is automatically shown on the Display Screen.
Press  ▲ or  ▼ to select the type of paper, and then press the  OK button.
The printer now starts feeding the paper.
Note• For  details  on  types  of  paper  to  select,  see  the  Paper  Reference  Guide.    (See  "Types  of...

Note•If the  Tab Selection screen  is not displayed, press the  Menu button.
2.Press the  OK button.
The  Paper Menu  is displayed.
3. Press  ▲ or  ▼ to select  Paper Details , and then press the  OK button.
4. Press  ▲ or  ▼ to select the type of paper, and then press the  OK button.
5. Press  ▲ or  ▼ to select  Width Detection , and then press the  OK button.
6. Press  ▲ or  ▼ to select  Off, and then press the  OK button.
Load paper in the desired position to start printing from
Follow these...

To start printing from the current position, close the Top Cover.
To reposition the paper, lift the Release Lever.Handling Paper 
>
 Handling sheets 
>Printing From a Desired Starting PointiPF83007808
 

5.Keeping the right edge of the paper aligned with the extended line of the paper alignment line (a) on the right side of
the printer and the position from which to start printing aligned with the groove (b) at the far end of the platen, load
the paper.Handling Paper 
>
 Handling sheets 
>iPF8300Printing From a Desired Starting Point7809
 

6.Lower the Release Lever and close the Top Cover.
Removing Sheets
Remove sheets from the printer as follows.
1. On the  Tab Selection screen  of the Control Panel, press  ◀ or  ▶ to select the Paper tab (
).
Note•If the  Tab Selection screen  is not displayed, press the  Menu button.
2.Press the  OK button.
The  Paper Menu  is displayed.
3. Press  ▲ or  ▼ to select  Eject Paper , and then press the  OK button.
4. Press  ▲ or  ▼ to select " Yes", and then press the  OK button.
The paper is...

5.Open the Top Cover, lift the Release Lever, and remove the sheet.
6.Lower the Release Lever and close the Top Cover.
Handling Paper 
>
 Handling sheets 
>iPF8300Removing Sheets7811
 

Output Stacker
Output Stacker  ............................................................................................................................................... 812
Using the Output Stacker ................................................................................................................................ 813
Storing the Output Stacker .............................................................................................................................. 819
Output...