Canon Imageprograf Ipf815 User Guide
Have a look at the manual Canon Imageprograf Ipf815 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
2. Keeping the right edge of the paper aligned with the extended line of the Paper Alignment Line (a) on the right side of the printer, load the paper so that the near edge is aligned with the groove (b) at the far end of the Platen. In this case, advance the paper as far into the paper feed slot as possible because it will be printed starting at that position. 3. Lower the Release Lever and close the Top Cover. 4. If no print job has been received from the computer, press ▲ or ▼ to select of the type of paper loaded, and then press the OK button. 5. When "Width Detection OFF. OK to continue?" is shown on the Display Screen, press ▲ or ▼ to select " Leave OFF " and then press the OK button. 6. Check the position of the loaded paper and press the OK button. 7. Press ▲ or ▼ to select the paper size, and then press the OK button. Handling Paper > Handling sheets > iPF815 Manually Loading Paper to the Position for Printing 7 655
Note • If a print job received requires paper larger than the selected paper, it may soil the Platen. Removing Sheets Remove sheets from the printer as follows. 1. Press the Load/Eject button. Note • Paper cannot be ejected by using the Load/Eject button when print jobs are in progress or during the ink drying period. Before ejecting paper, press the Stop button to cancel printing, print job process- ing, or ink drying. 2. Press the OK button to eject the paper. The paper is ejected from the front of the printer. Handling Paper > Handling sheets > Removing Sheets iPF8157 656
3. As you hold the sheet, lift the Release Lever and remove the sheet. 4. Lower the Release Lever. Handling Paper > Handling sheets > iPF815 Removing Sheets 7 657
Output Stacker Stationary Output Stacker ............................................................................................................................... 658 Using the Stationary Output Stacker ............................................................................................................... 659 Stowing the Stationary Output Stacker ........................................................................................................... 661 Wheeled Output Stacker ................................................................................................................................. 663 Using the Wheeled Output Stacker ............................................................................................................. 663Stationary Output Stacker a. Output Stacker A cloth tray that catches ejected documents. b. White tag A point of reference for attaching the Output Stacker in the right direction. c. Basket Arm R and Basket Arm L Holds the Basket Rod (tag side) attached to the Output Stacker. When the Output Stacker is not used, push it down and store it next to the Stand Leg. d. Basket Rod (tag side) and Basket Rod (cord side) Holds the cloth Output Stacker securely in specific positions. Handling Paper > Output Stacker > Stationary Output Stacker iPF8157 658
e. Basket Rod Keeps Basket Arm R and Basket Arm L at the same angle. f. Rear Holder Holds the middle of the Basket Rod (cord side). (See "Using the Stationary Output Stacker .") →P.659 Note • The printer can be used with either a Stationary Output Stacker or a separate, mobile Wheeled Output Stack- er. The Stationary Output Stacker is normally provided as the standard stacker, but the Wheeled Output Stackermay be the standard stacker in some sales regions. If the Wheeled Output Stacker has been provided as the standard stacker, the Stationary Output Stacker is not included. For more information about the Wheeled Output Stacker, see "Wheeled Output Stacker." →P.663 Using the Stationary Output Stacker The Stationary Output Stacker can be used in three positions, as shown. • When storing printed documents on the Output Stacker Use position (1). • When the Output Stacker is not used Move the stacker into position (2). Handling Paper > Output Stacker > iPF815 Using the Stationary Output Stacker 7 659
• When the Media Take-up Unit is used, or when the Output Stacker is stored for long periods Lower it to position (3) for storage. (See "Stowing the Stationary Output Stacker.") →P.661 When using the Output Stacker again after storage, reattach the Basket Rod on the front of the Output Stacker to the tips of the left and right basket arms and pull the side rods out completely. • When printing on large, stiff sheets Use position (3). Important • When storing printed documents on the Output Stacker, always use it in position (1). If you do not, printed documents may not be dropped into the Output Stacker, and the printed surface may become soiled. • The Output Stacker can accommodate one sheet. When printing multiple pages, remove each sheet after it is printed. • Before using the Output Stacker, remove the Rewind Spool. If you do not, it may prevent printed documents from being held correctly, and they may be scratched. • The Output Stacker can hold printed documents from rolls that are 62 inches (1,575 mm) long. When print- ing longer documents, use the optional Media Take-up Unit. The Output Stacker locks into position if you lift it to position (1) or (2). To lower the Output Stacker, lift the front Basket Rod lightly to release the lock, and then lower the stacker. Handling Paper > Output Stacker > Using the Stationary Output Stacker iPF8157 660
Stowing the Stationary Output Stacker Stow the Stationary Output Stacker if you will use the Media Take-up Unit or if you will not use the Stationary Output Stacker for an extended period. 1. When the Output Stacker is in the position used when storing printed documents (a), lift the front Basket Rod gently to release the lock, lower the stacker toward the front (b), and push it all the way back. 2. Remove the front Basket Rod from the left and right Basket Arms. Roll up the Basket Cloth and put it at the back of the Bottom Stand Stay. Handling Paper > Output Stacker > iPF815 Stowing the Stationary Output Stacker 7 661
Important • When using the optional Media Take-up Unit, position the Basket Cloth and Basket Rod so they do not interfere with the Media Take-up Sensor (indicated by the dashed line). 3. Push in the left and right Basket Arm toward the back all the way, until they stop. Handling Paper > Output Stacker > Stowing the Stationary Output Stacker iPF8157 662
Wheeled Output Stacker An output stacker with casters, positioned in front of the printer. a. Output Stacker A cloth tray that catches ejected documents. The Output Stacker can be opened and closed using the rod in front. b. Output Stacker Ejection Guides Prevent printed documents from winding around the Roll Holder or being drawn into the Paper Feed Slot. Hold the Wheeled Output Stacker by these guides when moving it. c. Output Stacker Foot Stand Equipped with casters to facilitate moving it. d. Stopper Locks the Stand casters. Always release the Stopper before moving the printer. Moving the printer while the Stopper is locked may scratch the casters or the floor. Note • For instructions on assembling the Wheeled Output Stacker, see the setup guide provided with the Wheeled Output Stacker. • The printer can be used with either a Stationary Output Stacker or a separate, mobile Wheeled Output Stack- er. The Wheeled Output Stacker is normally provided as an optional accessory, but it may be the standard stack- er in some sales regions. If the Wheeled Output Stacker has been provided as the standard stacker, the Sta- tionary Output Stacker is not included. For more information about the Stationary Output Stacker, see "Stationary Output Stacker." →P.658 Using the Wheeled Output Stacker Positioning the Wheeled Output Stacker by the printer will prevent rolls from dropping on the floor after printing. The stacker is equipped with casters to facilitate moving it. Important • The Output Stacker can accommodate one sheet. When printing multiple pages, remove each sheet after it is printed. Handling Paper > Output Stacker > iPF815 Wheeled Output Stacker 7 663
Positioning the Wheeled Output Stacker by the printer 1. Holding the Output Stacker Ejection Guides (a), move the stacker between the printer Stand. 2. Lock the casters. Handling Paper > Output Stacker > Using the Wheeled Output Stacker iPF8157 664