Canon Eos Rebel T5i 700d Instruction Manual

231
The basics of easy, fully automatic wireless flash shooting are explained below.
Steps 1 to 4 and 6 apply to all 
wireless flash shooting. Therefore, 
these steps are omitted in the other 
wireless flash setups explained on 
the pages hereafter.
1Press the  button to raise the 
built-in flash.
  For wireless flash shooting, be sure 
to raise the built-in flash.
2Select [Flash control].
 Under the [z 1] tab, select [Flash 
control ], then press < 0>.
3Select [Evaluative].
  For [ E-TTL II meter. ],...

232
Easy Wireless Flash Shooting
4Select [Built-in flash settings].
 Select [ Built-in flash settings], then 
press < 0>.
5Select [EasyWireless].
  Under [ Built-in flash ], select 
[EasyWireless ], then press .
6Set [Channel].
  Set the transmission channel (1-4) to 
the same one as the slave unit.
7Take the picture.
 Set the camera and take picture in 
the same way as with normal 
shooting.
8Exit the wireless flash shooting.
 For [ Built-in flash ], select 
[NormalFiring ].
 Setting [ E-TTL II meter. ]...

233
Easy Wireless Flash Shooting
You can have multiple slave units fire as if they were a single Speedlite. 
This is convenient when you need a large flash output.
Basic settings:
Flash mode : E-TTL II
E-TTL II meter. : Evaluative
Built-in flash : EasyWireless
Channel : (Same as slave units)
All the slave units will fire at the same 
output and be controlled to obtain a 
standard exposure.
No matter what the slave ID is (A, B, or 
C), all the slave units will fire as one 
group.
If the flash exposure...

234
This section describes fully automatic 
wireless flash shooting with one external 
Speedlite and the built-in flash.
You can change the flash ratio between 
the external Speedlite and built-in flash 
to adjust how the shadows look on the 
subject.
On the menu screens, the  and 
< 1 > icons refer to the external 
Speedlite, and the < 3> and < 2> 
icons refer to the built-in flash.
1Select [CustWireless].
  Follow step 5 on page 232 to select 
[CustWireless], then press < 0>.
2Select [Wireless func.]....

235
Custom Wireless Flash Shooting
Multiple Speedlite slave units can be treated as one flash unit or 
separated into slave groups whose flash ratio can be set.
The basic settings are shown below. By changing the [Firing group ] 
setting, you can shoot with various wi reless flash setups with multiple 
Speedlites.
Basic settings:
Flash mode : E-TTL II
E-TTL II meter. : Evaluative
Wireless func. : 0
Channel : (Same as slave units)
[ 1 All] Using multiple slave Speedlites as one flash unit
This is...

236
Custom Wireless Flash Shooting
[1  (A:B)] Multiple slave units in multiple groups
Divide the slave units into groups A and 
B and change the flash ratio to obtain 
the desired lighting effect.
Refer to your Speedlite’s instruction 
manual to set one slave unit’s slave ID 
to A (Group A) and the other slave unit’s 
ID to B (Group B), and position them as 
shown in the illustration.
1Select [Wireless func.].
 Follow step 2 on page 234 to select 
[0 ], then press < 0>.
2Set [Firing group] to [1...

237
Custom Wireless Flash Shooting
The built-in flash can also be added to wireless flash shooting explained 
on pages 235-236.
The basic settings are shown below. By changing the [Firing group ] 
setting, you can shoot with various wireless flash setups of multiple 
Speedlites complemented with the built-in flash.
1Basic settings:
Flash mode : E-TTL II
E-TTL II meter. : Evaluative
Wireless func. : [ 0+3 ]
Channel : (Same as slave units)
2Select [Firing group].
 Select the firing group, then set the...

238
When [Flash mode] is set to [E-TTL II], flash exposure compensation 
can be set. The flash exposure co mpensation settings (see below) 
which can be set will differ depending on the [ Wireless func.] and 
[Firing group ] settings.
[Flash exp. comp.]
 The flash exposure compensation is 
applied to the built-in flash and all 
external Speedlites.
[2  exp. comp.]
 The flash exposure compensation is 
applied to the built-in flash.
[1  exp. comp.]
 The flash exposure compensation is 
applied to all...

239
Other Settings
When [Flash mode] is set to [Manual flash ], flash exposure can be set 
manually. The flash output settings ([ 1 flash output ], [Group A 
output ], etc.) that can be set will differ depending on the [ Wireless 
func. ] setting (see below).
[Wireless func. 0]
 [Firing group: 1 All]: The manual 
flash output setting will be applied to 
all the external Speedlites.
  [Firing group:  1 (A:B) ]: You can set 
the flash output separately for slave 
groups A and B.
[Wireless func. 0+3 ]...

240
COPY