Canon 5dsr Manual

371
You can crop a JPEG image and save it as another image. You can 
crop 3, K , 5 , a  and b JPEG images.  JPEG c and RAW images 
cannot be cropped.
1Select [Cropping].
 Under the [x 2] tab, select 
[Cropping ], then press < 0>.
 An image is displayed.
2Select an image.
 Turn the < 5> dial to select the 
image you want to crop.
 If you press the  button and turn 
the < 6> dial counterclockwise, you 
can select an image from the index 
display.
3Set the cropping frame size, 
aspect ratio, position,...

N Cropping JPEG Images
372
Moving the Cropping Frame
Use < 9> to move the frame over the image vertically or 
horizontally. Move the cropping frame until it covers the desired 
image area.
Switching the Cropping Frame Orientation
Pressing the < B> button will toggle the cropping frame between 
the vertical and horizontal orientatio ns. This enables you to create a 
vertically oriented image from a horizontal image.
4Check the image area to be 
cropped.
 Press the < Q> button.
 The image area to be...

373
11
Sensor Cleaning
The camera has a Self Cleaning Sensor Unit to 
automatically shake off dust adhered to the image 
sensor’s front layer (low pass filter).
The Dust Delete Data can also be appended to the 
image so that the dust spots remaining can be deleted 
automatically by Digital Photo Professional (EOS 
software, p.521).
Smudges adhering to the front of the sensorBesides dust entering the camera from outside, in rare cases, 
lubricant from the camera’s internal parts may adhere to the front of...

374
Whenever you set the power switch to  or , the Self 
Cleaning Sensor Unit operates to aut omatically shake off the dust on 
the front of the sensor. Normally, you need not pay attention to this 
operation. However, you can choos e to perform sensor cleaning 
manually, or disable it.
1Select [Sensor cleaning].
Under the [5 3] tab, select [ Sensor 
cleaning ], then press < 0>.
2Select [Clean now f].
Select [ Clean now f], then press 
< 0 >.
 Select [ OK].
 The screen will indicate that the 
sensor...

375
Normally, the Self Cleaning Sensor Unit will eliminate most of the dust 
that may be visible on captured images. However, in case visible dust 
still remains, you can append the Dust Delete Data to the image for 
erasing the dust spots later. The Dust Delete Data is used by Digital 
Photo Professional (EOS software, p.521) to erase the dust spots 
automatically.
Prepare a solid white object such as a sheet of paper.
 Set the lens focal length to 50 mm or longer.
 Set the lens’s focus mode switch...

3 Appending Dust Delete Data N
376
3Shoot a solid-white object.
At a distance of 20 cm - 30 cm (0.7 ft. 
- 1.0 ft.), fill the viewfinder with a 
patternless, solid-white object and 
take a picture.

The picture will be taken in aperture-
priority AE mode at an aperture of f/22.
 Since the image will not be saved, the 
data can still be obtained even if there 
is no card in the camera.
 When the picture is taken, the camera 
will start collecting the Dust Delete 
Data. When the Dust Delete Data is...

377
Dust that could not be removed by the automatic sensor cleaning can 
be removed manually with a commercially-available blower, etc. Before 
cleaning the sensor, detach the lens from the camera.
The image sensor is extremely delicate. If the sensor needs to be 
cleaned directly, having it done by a Canon Service Center is 
recommended.
1Select [Sensor cleaning].
 Under the [5 3] tab, select [Sensor 
cleaning ], then press < 0>.
2Select [Clean manually].
3Select [OK].
In a moment, the reflex mirror...

3 Manual Sensor Cleaning N
378
While cleaning the sensor, never do any of the following. If the 
power is cut off, the shutter will close and the shutter curtains and 
image sensor may get damaged.
• Setting the power switch to < 2>.
• Removing or inserting the battery.
 The surface of the image sensor is  extremely delicate. Clean the sensor 
with care.
 Use a plain blower without any brush  attached. A brush can scratch the 
sensor.
 Do not insert the blower tip inside the camera beyond the lens...

379
12
Printing Images and Transferring
Images to a Computer
 Printing  (p.382)
You can connect the camera directly to a printer and print 
out the images on the card. The camera is compliant with 
“ w PictBridge”, which is the standard for direct printing.
 Digital Print Order Format (DPOF)  (p.389)
DPOF (Digital Print Order Format) enables you to print 
images recorded on the card according to your printing 
instructions such as the image selection, quantity to print, 
etc. You can print multiple...

380
The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor.
1Set the camera’s power switch to 
.
2Set up the printer.
For details, refer to the printer’s 
instruction manual.
3Connect the camera to a printer.
Use the interface cable provided with 
the camera.
 When connecting the cable to the 
camera, use the cable protector 
(p.36). Connect the cable to the 
digital terminal with the plug’s 
< > icon facing the back of the 
camera.
 To...