Brother MFC 9010CN User Manual
Have a look at the manual Brother MFC 9010CN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Safety and legal39 A CAUTION After you have just used the machine, some internal parts of the machine will be extremely hot. To prevent injury, when you open the top or back cover (back output tray) of the machine, DO NOT touch the shaded parts shown in the illustration. To prevent injuries, be careful not to put your hands on the edge of the machine under the document cover, the scanner, or the top cover as shown in the illustrations. To prevent injuries, be careful not to put your fingers in the areas shown in the illustrations.
40 IMPORTANT The fuser unit is marked with a Caution label. Please DO NOT remove or damage the label. Important safety instructionsA 1 Read all of these instructions. 2 Save them for later reference. 3 Follow all warnings and instructions marked on the product. 4 Unplug this product from the wall outlet before cleaning inside of the machine. DO NOT use liquid or aerosol cleaners. Use a dry, lint-free cloth for cleaning. 5 DO NOT place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6 Slots and openings in the cabinet at the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heater. This product should never be placed in a built-in installation unless adequate ventilation is provided. 7 This product should be connected to an AC power source within the range indicated on the rating label. DO NOT connect it to a DC power source or inverter. If you are not sure, contact a qualified electrician. 8 This product is equipped with a 3-wire grounded plug. This plug will only fit into a grounded power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, call your electrician to replace your obsolete outlet. DO NOT defeat the purpose of the grounded plug. 9 Use only the power cord supplied with this machine. 10 DO NOT allow anything to rest on the power cord. DO NOT place this product where people can walk on the cord. 11 If an extension cord is used with this product, make sure that the total ampere ratings on the products plugged into the extension cord DO NOT exceed the extension cord ampere rating. Also, make sure that the total of all products plugged into the AC power outlet does not exceed 15 amperes (US only).
Safety and legal41 A 12 Use the product in a well-ventilated area. 13 The power cord, including extensions, should be no longer than 16.5 feet (5 meters).DO NOT share the same power circuit with other high powered appliances, such as an air conditioner, copier, shredder, and so on. If you cannot avoid using the machine with these appliances, we recommend that you use a voltage transformer or a high-frequency noise filter. Use a voltage regulator if the power source is not stable. 14 DO NOT place anything in front of the machine that will block printed pages. DO NOT place anything in the path of printed pages. 15 Wait until pages have exited the machine before picking them up. 16 Never push objects of any kind into this product through cabinet slots, since they may touch dangerous voltage points or short out parts resulting in the risk of fire or electric shock. Never spill liquid of any kind on the product. DO NOT attempt to service this product yourself because opening or removing covers may expose you to dangerous voltage points and other risks and may void your warranty. Refer all servicing to a Brother Authorized Service Center. For the location of your nearest Brother Authorized Service Center, please call: In USA : 1-877-BROTHER (1-877-276-8437) In Canada : 1-877-BROTHER 17 Unplug this product from the AC power outlet and refer all servicing to Brother Authorized Service Personnel under the following conditions: „ When the power cord is damaged or frayed. „ If liquid has been spilled into the product. „ If the product has been exposed to rain or water. „ If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. „ If the product has been dropped or the cabinet has been damaged. „ If the product exhibits a distinct change in performance, indicating a need for service. 18 To protect your product against power surges, we recommend the use of a power protection device (Surge Protector). 19 To reduce the risk of fire, electric shock and injury to people, note the following: „DO NOT use this product near appliances that use water, a swimming pool or in a wet basement. „ DO NOT use the machine during an electrical storm (there is the remote possibility of an electrical shock). „ DO NOT use this product in the vicinity of a gas leak.
42 Federal Communications Commission (FCC) Declaration of Conformity (USA only)A declares, that the products Product Name: MFC-9010CN comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:„ Reorient or relocate the receiving antenna. „ Increase the separation between the equipment and receiver. „ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. „ Call the dealer or an experienced radio/TV technician for help. IMPORTANT • Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s authority to operate the equipment. • Brother cannot accept any financial or other responsibilities that may be the result of your use of this information, including direct, special or consequential damages. There are no warranties extended or granted by this document. Industry Canada Compliance Statement (Canada only) A This Class B digital apparatus complies with Canadian ICES–003. Cet appareil numérique de la classe B est conforme à la norme NMB–003 du Canada.Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA TEL: (908) 704-1700
Safety and legal43 A Disconnect deviceA This product must be installed near an AC power outlet that is easily accessible. In case of emergencies, you must disconnect the power cord from the AC power outlet to shut off power completely. LAN connectionA CAUTION DO NOT connect this product to a LAN connection that is subject to over-voltages. International ENERGY STAR® Qualification StatementA The purpose of the International ENERGY STAR® Program is to promote the development and popularization of energy-efficient office equipment. As an ENERGY STAR ® Partner, Brother Industries, Ltd. has determined that this product meets the ENERGY STAR ® specifications for energy efficiency.
44 Libtiff Copyright and LicenseA Use and Copyright Copyright© 1988-1997 Sam Leffler Copyright© 1991-1997 Silicon Graphics, Inc. Permission to use, copy, modify, distribute, and sell this software and its documentation for any purpose is hereby granted without fee, provided that (i) the above copyright notices and this permission notice appear in all copies of the software and related documentation, and (ii) the names of Sam Leffler and Silicon Graphics may not be used in any advertising or publicity relating to the software without the specific, prior written permission of Sam Leffler and Silicon Graphics. THE SOFTWARE IS PROVIDED AS-IS AND WITHOUT WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Safety and legal45 A TrademarksA The Brother logo is a registered trademark of Brother Industries, Ltd. Brother is a registered trademark of Brother Industries, Ltd. Multi-Function Link is a registered trademark of Brother International Corporation. Adobe, Flash, Illustrator, PageMaker, Photoshop, PostScript and PostScript 3 are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and/or other countries. Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and other countries. Apple, Macintosh, Safari and TrueType are trademarks of Apple Inc., registered in the United States and other countries. Intel, and Pentium are trademarks of Intel Corporation in the U.S. and other countries. AMD is a trademark of Advanced Micro Devices, Inc. PowerPC is a registered trademark of IBM in the United States and/or other countries. Epson is a registered trademark and FX-80 and FX-850 are trademarks of Seiko Epson Corporation. IBM and Proprinter are either registered trademarks or trademarks of International Business Machines Corporation in the United States and/or other countries. Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of Nuance Communications, Inc. or its affiliates in the United States and/or other countries. All other trademarks are the property of their respective owners.
46 B OptionsB This machine has the following optional accessory. You can increase the capabilities of the machine with this item. OptionsB SO-DIMM memory
Options47 B Memory boardB MFC-9010CN has 64 MB of standard memory and one slot for optional memory expansion. You can expand the memory up to 576 MB by installing dual in-line memory modules (SO-DIMMs). When you add the optional memory, it increases the performance for both copier and printer operations. In general, the machine uses industry-standard SO-DIMM with the following specifications: Type: 144 pin and 64 bit output CAS latency: 2 Clock frequency: 100 MHz or more Capacity: 64, 128, 256 or 512 MB Height: 1.25 in. (31.75 mm) Dram Type: SDRAM 2 Bank The following web sites sell memory modules:http://www.crucial.com/ http://www.kingston.com/ http://goldenram.com/ http://www.buffalo-technology.com/ Note • There might be some SO-DIMMs that will not work with the machine. • For more information, call Brother Customer Service. Installing extra memoryB aTurn off the machine’s power switch. bDisconnect the interface cable from the machine, and then unplug the power cord from the AC power outlet. Note Be sure to turn off the machine’s power switch before you install or remove the SO-DIMM. cRemove the plastic (1) and then metal (2) SO-DIMM covers. dUnpack the SO-DIMM and hold it by its edges. IMPORTANT To prevent damage to the machine from static electricity, DO NOT touch the memory chips or the board surface. 1 2
48 eHold the SO-DIMM by the edges and align the notches in the SO-DIMM with the protrusions in the slot. Insert the SO-DIMM diagonally (1), then tilt it toward the interface board until it clicks into place (2). fPut the metal (2) and then the plastic (1) SO-DIMM covers back on. gPlug the machine’s power cord back into the AC power outlet first, and then connect the interface cable. hTurn on the machine’s power switch. Note To make sure that you have installed the SO-DIMM properly, you can print the user settings page that shows the current memory size. (See User Settings List on page 105.) 12 1 2