Brother MFC 9010CN User Manual

9
2
2
Loading paper and 
print media
2
The machine can feed paper from the 
standard paper tray.
When you put paper into the paper tray, note 
the following:„ If your application software supports 
paper size selection on the print menu, 
you can select it through the software. If 
your application software does not 
support it, you can set the paper size in 
the printer driver or by using the control 
panel buttons.
Loading paper in the standard 
paper tray2
Printing on plain paper, thin paper or...

Chapter 2
10
cFan the stack of paper well to avoid 
paper jams and misfeeds.
 
dPut paper in the tray, and make sure that 
the paper is below the maximum paper 
mark (1). The side to be printed on must 
be face down.
 
IMPORTANT
Make sure the paper guides touch the 
sides of the paper so it will feed properly. 
If you do not do this, it may cause damage 
to your machine.
 
ePut the paper tray firmly back in the 
machine. Make sure that it is completely 
inserted into the machine.
fLift up the support...

Loading paper and documents11
2
Loading paper in the manual 
feed slot2
You can load envelopes and special print 
media one at a time into this slot. Use the 
manual feed slot to print or copy on labels, 
envelopes or thicker paper.
Printing on plain paper, recycled 
paper or bond paper from the manual 
feed slot
2
Before loading, press the corners and sides 
of the envelopes to make them as flat as 
possible.
Note
The machine automatically turns on the 
Manual Feed mode when you put paper in 
the...

Chapter 2
12
Printing on thick paper, labels, 
envelopes or small paper
2
When the back output tray is pulled down, the 
machine has a straight paper path from the 
manual feed slot through to the back of the 
machine. Use this paper output method when 
you want to print on thick paper, labels, 
envelopes or paper that is smaller than 
4.1 ×5.8 in. (or A6 size).
Note
• Remove each printed sheet or envelope 
immediately to prevent a paper jam.
• The machine automatically turns on the  Manual Feed mode...

Loading paper and documents13
2
eUsing both hands, put one sheet of 
paper or one envelope in the manual 
feed slot until the front edge of the paper 
or envelope touches the paper feed 
roller. When you feel the machine pull in 
the paper, let go.
 
 
Note
• Put the paper into the manual feed slot with the side to be printed face up.
• Make sure that the print media is straight  and in the proper position on the manual 
feed slot. If it is not, the paper may not be 
fed properly, resulting in a skewed...

Chapter 2
14
Unprintable area2
Unprintable area for copies2
The figures below show unprintable areas.
Note
This unprintable area shown above is for a single copy or a 1 in 1 copy using Letter size paper. 
The area that cannot be printed on will vary by paper size.
 
Unprintable area when printing from a computer2
When using the printer driver the printable area is smaller than the paper size, as shown below.
Note
The area that cannot be printed on may vary depending on the paper size and the printer...

Loading paper and documents15
2
Acceptable paper and 
other print media
2
Print quality may vary according to the type of 
paper you are using.
You can use the following types of print 
media: thin paper, plain paper, thick paper, 
bond paper, recycled paper, labels or 
envelopes.
For best results, follow the instructions below:„ Use paper made for plain paper copying.
„ Use paper that is 20 to 24 lb 
(75 to 90 g/m
2).
„ DO NOT put different types of paper in the 
paper tray at the same time because it...

Chapter 2
16
Paper capacity of the paper trays2
1Folio size is 8.5 in.  × 13 in. (215.9 mm x 330.2 mm)
Recommended paper specifications2
The following paper specifications are suitable for this machine.
Paper sizePaper typesNo. of sheets
Paper Tray A4, Letter, Legal,  Executive, A5, A5 (Long 
Edge), A6, B5 (ISO), B6 
(ISO) and Folio
1
Plain paper, Thin paper 
and Recycled paper up to 250 
[20lb(80g/m
2)]
Manual feed slot
(Manual Feed) Width: 3.0 to 8.66 in. 
(76.2 to 220 mm)
Length: 4.57 to 16 in. 
(116...

Loading paper and documents17
2
Handling and using special 
paper2
The machine is designed to work well with 
most types of xerographic and bond paper. 
However, some paper variables may have an 
effect on print quality or handling reliability. 
Always test samples of paper before 
purchasing to ensure desirable performance. 
Store paper in its original packaging and keep 
it sealed. Keep the paper flat and away from 
moisture, direct sunlight and heat.
Some important guidelines when selecting 
paper...

Chapter 2
18
Envelopes2
Most envelopes will be suitable for your 
machine. However, some envelopes may 
have feed and print-quality problems 
because of the way they have been made. A 
suitable envelope should have edges with 
straight, well-creased folds and the leading 
edge should not be thicker than two sheets of 
paper. The envelope should lie flat and not be 
of baggy or flimsy construction. You should 
buy quality envelopes from a supplier who 
understands that you will be using the 
envelopes in...