Bizfon 680 Instructions Manual

Bizfon Owner’s Guide31
Section 4
Using your Bizfon 
with Other Office 
Equipment
This section gives information on how to 
extend your Bizfon communications system 
to work with other equipment you may have 
in your office.
Fax MachinesIf you have a dedicated fax line that you 
would also like to use for outgoing calls, 
connect this line to the blue “Incoming Tele-
phone Lines” jack labeled “6”. Then connect 
your fax machine to the yellow “Telephones” 
jack labeled “8”. After being configured by...

Section 4 Using your Bizfon with Other Office Equipment
32 Bizfon, Inc.
mono converter that has a single RCA jack 
(Radio Shack part number: 42-2444). 
Connect the cable to your audio source, and 
plug it into the Music-On-Hold (MOH) con-
nector on the Bizfon 680. Set the levels on 
your audio source. If it is distorted, turn 
down the volume on your audio source. 
Note:
Please be aware that you may need ASCAP 
authorization to play music to callers on 
hold. For more information, contact ASCAP 
at (212)...

Section 4 Using your Bizfon with Other Office Equipment
Bizfon Owner’s Guide33
Input for M usic on Hold
Daisy Chain Connecters
For Future Use
Ext 201 Ext 202 Ext 203 Ext 204 Ext 205 Ext 206
Ext 207 Ext 208 Network Connecter
For Factory Use
Only
Flash Card Port
For Future Upgrades Em ergency Phone Ext
F or P ow er Failu reCO 1+2CO 2 CO 3+4CO 4 CO 5+6CO 6O u tp u t to  P A
For Future UseRelay for Door Lock
For Future Use
Serial Port
For Factory Use Only
Power
Cord
Blue Button
For Diagnostics 

Section 4 Using your Bizfon with Other Office Equipment
34 Bizfon, Inc. 

Bizfon Owner’s Guide35
Appendix A
Startup/Test 
Button
Using the Star-
tup/Test ButtonAfter connecting your telephone lines and 
telephones, you can use the Startup/Test but-
ton to confirm that your Bizfon 680 is prop-
erly set up.
1. Press the Startup/Test button (the blue 
button in the center of the Bizfon 680) 
once. A welcome message is played 
along with a notification that the system 
cannot be used for incoming or outgoing 
calls while being tested. When you press 
the button again, calls in...

Appendix A Startup/Test Button
36 Bizfon, Inc.
Important!
The results of this test are used by the Bizfon 
680 to determine which telephone lines may 
be used to make outgoing calls. Be sure to 
run this test each time after making any 
changes to the Incoming Telephone Lines.
3. Press the button again. A message is 
played indicating that the Incoming Tele-
phones Lines test is complete and that 
now the diagnostics will test the exten-
sions by consecutively ringing each tele-
phone connected to the...

Bizfon Owner’s Guide37
Appendix B
Bizfon 680 
Installation 
Considerations
Mounting 
Bracket It is recommended that you do not use your 
Bizfon 680 without the mounting bracket 
attached, whether mounted and attached to a 
wall or when resting on a table or desk top. 
Attaching the 
BracketBefore attaching the bracket, you may want 
to write down the serial number that is on the 
back of the Bizfon 680 for registration pur-
poses. 
1. Hold the Bizfon 680 in your left hand 
with the power cord facing...

Appendix B Bizfon 680 Installation Considerations
38 Bizfon, Inc.
2. Hold the bracket in your right hand, with 
the side with the large rectangular open-
ing facing the back of the Bizfon 680 and 
align the four tabs on the mounting 
bracket with the four slots on the bottom 
of the Bizfon 680, as shown below.   

Appendix B Bizfon 680 Installation Considerations
Bizfon Owner’s Guide39
3. Slide the bracket until it snaps in place 
with the tabs secured in the slots, as shown 
below.
Removing the 
Bracket1. Apply downward pressure with your 
thumb to the portion of the mounting 
bracket that protrudes into the space 
where the Voice  Vault option slot is 
located, as shown below.
2. While applying downward pressure, 
simultaneously slide the bracket in the 
direction of the power cord. 
3. Pull the bracket away...

Appendix B Bizfon 680 Installation Considerations
40 Bizfon, Inc.
Wall Mount
1. Position the Bizfon 680 within four (4) 
feet of a power outlet.  
2. Attach the bracket to the wall vertically, 
using the enclosed screws, or screws and 
drywall anchors, as appropriate to the 
type of wall on which you are mounting 
the Bizfon 680, as shown in the figures 
above.  When using the anchors on dry-
wall, pre-drill a 3/16” pilot hole. When 
using the anchors on concrete, pre-drill a 
1/4” pilot hole.
3. Lock...