Barco Projector Cineversum 80 Quickstart Manual

13. Projection Stop (Standby or Economic Standby mode)
After the power down time, the standby LED on the Cine VERSUM 80 stays blinking on a beat of 0.3s on, 0.3s
off for approximately 1 minute, named the cool down time. A new start up command will be executed after the
cool down period only.
R5976468 CINE VERSUM SYSTEM 0311200387 

13. Projection Stop (Standby or Economic Standby mode)
88R5976468 CINE VERSUM SYSTEM 03112003 

14. Switching linked displays To and Out Standby
14. SWITCHING LINKED DISPLAYS TO AND OUT
STANDBY
Overview
• Switching by means of the Cine VERSUM Master
• Direct Switching of the Linked Display
14.1 Switching by means of the Cine VERSUM Master
Overview
• Switching In/Out Standby using the Jog Dial
• Switching In/Out Standby using the Remote Control
14.1.1 Switching In/Out Standby using the Jog Dial
How to switch one or more displays To or Out standby mode
1. From the startup menu on the graphical...

14. Switching linked displays To and Out Standby
Message Command sent to display
_______________________________
_______________________________
_______________________________
Menu 14-5
Recap
If the status of a display is On, via the display settings menu the display can be switched into the standby mode. If the status of a
display is Standby, then the display can be switched to the operation mode.
14.1.2 Switching In/Out Standby using the Remote Control
Make sure the Remote Control suits the address of...

14. Switching linked displays To and Out Standby
Message
Command sent to display
Menu 14-10
Recap
If the status of a display is On, via the display settings menu the display can be switched into the standby mode. If the status of a
display is Standby, then the display can be switched to the operation mode.
For a display with status ’standby’, counteracting these status can be made using the jog dial on the Cine VERSUM Master or via
the on-screen of an active display.
14.2 Direct Switching of the Linked...

14. Switching linked displays To and Out Standby
92R5976468 CINE VERSUM SYSTEM 03112003 

15. Module Address Read out/Change
15. MODULE ADDRESS READ OUT/CHANGE
15.1 Default address of the Modules
Introduction
To allow separate remote access to the different modules, an individual address has to be stored in each module.
Overview default address modules
Each module leaves the factory with a default address:
ModuleAddress
Cine VERSUM Master1
Cine VERSUM 809
Cine VERSUM 509
Cine VERSUM 1209
15.2 Reading out/Changing the stored addresses
Overview
• Reading out the stored address
• Changing the...

15. Module Address Read out/Change
Reading out the stored address using Display setting menu (exclusive Cine VERSUM Master)
1. Using the jog dial on the Cine VERSUM Master or the Remote control keys, successively selects Main menu, Installation and
Display list.
The display list (On screen,menu 15-4; Graphical display, menu 15-3) sums up the linked displays. The display name is preceded
by its address number. The address number can also be find in the display settings menu of the respective display...

15. Module Address Read out/Change
Image 15-1
Example of address set up
Changing the stored address of a linked display
1. Successively scroll throughthe menus Main (Cine VERSUM System), Installation, Display list.
2. Select in the display list the display you desire to change the address.
3. Press the jog dial or pressENTERto confirm.
The display settings menu for that specific display appears on the screen and on the graphical display.
4. Scroll through the display setting items, using the jog dial or...

15. Module Address Read out/Change
Changing the stored address of the Cine VERSUM Master
1. Successively scroll through the menus Main (Cine VERSUM System), Service.
2. Select in the Service list item IR Address 001
3. Press the jog dial or pressENTERto confirm.
A text box appears on the screen (menu 15-11) and in the graphical display (menu 15-12) requesting to enter a new 3 digit
address value.
4. Enter a 3 digit number, from 000 to 256, using the number keys on the RCU.
Note:As the Remote Control can...