Barco Projector Cineversum 80 Quickstart Manual

18. Additional settings Cine VERSUM Master
18. ADDITIONAL SETTINGS CINE VERSUM MASTER
Overview
• Output Resolution set up
• Display Internal Generated Pattern
• Shutdown Automatic when no signal
• Source Transition
• On Screen Display Configuration
• On-Screen Display Language
• Display Name Change
18.1 Output Resolution set up
Why Output Resolution set up?
In case the digital video distribution system contains a combination of a Cine VERSUM 50 (Resolution 1280/768), a Cine VERSUM
80 (Resolution...

18. Additional settings Cine VERSUM Master
Image 18-1
Picture on display
Image 18-2
Picture on display
18.2 Display Internal Generated Pattern
How to display an internal pattern
In total 10 different internal patterns (Generated in the Cine VERSUM Master) can be displayed instead of the selected source. To
select a pattern, carry out the following steps:
1. Select the INSTALLATION menu (see Loading a File, page 97).
2. Select item INTERNAL PATTERN by rotating the jog dial on the Master or the↑or↓keys on...

18. Additional settings Cine VERSUM Master
Image 18-3
Available testpatterns
18.3 Shutdown Automatic when no signal
How to setup the automatic shutdown
If no input signal is available for a delay of minimum 40 seconds, the Cine VERSUM Master can be setup for automatic shutdown
(Standby mode).
1. Select the INSTALLATION menu (see Loading a File, page 97)
2. Select itemWHEN NO SIGNALby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the...

18. Additional settings Cine VERSUM Master
18.4 Source Transition
Source transition
Seamless transition mode can be applied during input source switching. There is a choice between 14 different effects which render
the transitions more enjoyable.
How to enter the source transition effect
1. Select the INSTALLATION menu (see Loading a File, page 97)
2. Select itemSOURCE TRANSITIONby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the...

18. Additional settings Cine VERSUM Master
Image 18-4
•PressthekeyTEXTon the Remote Control. The OSD’s, included Menu, Bar scale and Message are disabled. To reactivate
the OSD, press the keyTEXTagain. Attention, only the OSD’s (including MENU, BAR SCALE and MESSAGE) with status ’On’
will be active again.
• Via the OSD configuration menu. Disabling and enabling the display (=changing the status) for respective Menu, Bar scale and
Messages, has to be done for each item separately.
18.5.2 Status Change of...

18. Additional settings Cine VERSUM Master
18.5.3 On Screen Display Position Alignment
How to define the position of the OSD
The position of the OSD for the Menu and the Bar scale is adjustable. The vertical and the horizontal position of the OSD are
adjustable and are located in the menu below the respective OSD name, Menu position and Bar scale position. The procedure is
for both the same. Follow the next steps:
1. Select the OSD adjustable item you want to change by rotating the jog dial on the Master...

18. Additional settings Cine VERSUM Master
18.7 Display Name Change
Where to find the display RENAME function
InstallationInput Slots
File Service
Display List
Internal Pattern
W hen no signal
Source Transition
OSD configuration
Language
Keystone
Global Keystone:Yes
Output: [Largest]
Default Input Balance
Back
Main Menu/Installation/Display List/Display Settings
Display Settings Switch OFF
 Display Info
 Rename
 IR Address 009
 Diagnosis
Back
Cine VERSUM r01
Display List1 CV50  On
2 CV80 On
3 CV120...

18. Additional settings Cine VERSUM Master
134R5976468 CINE VERSUM SYSTEM 03112003 

19. Picture in Picture (PIP)
19. PICTURE IN PICTURE (PIP)
Overview
• Turning On/Off the Picture in Picture
• Selecting Input Source for PIP Window
• Configuration of the PIP Window
What is Picture in Picture
If PIP is enabled, a window is inserted in the active image, in which the image of another selected input source will be displayed.
The position and the size of the window is adjustable. How to turn On/Off and adjusting the size and position of the PIP window,
see below.
19.1 Turning On/Off the...

19. Picture in Picture (PIP)
Image 19-1
Picture in Picture
When a PiP window is on the screen, zapping over inputs change only the PiP window. When the same source
is pressed twice, the selected source becomes the main window and the PiP window disappears.
19.3 Configuration of the PIP Window
How to configure the PIP window manually
1. Select the PIP Configuration menu (Turning On/Off the Picture in Picture, page 135).
2. Select the item you desire to adjust by rotating the jog dial on the Master or the...