Barco Projector Cineversum 70 Quickstart Manual

9. Installation menu
How to change the language ?
1. Push the cursor key↑or↓to highlightOSD configuration. (menu 9-31)
2. PressENTERto select.
TheLanguageselection menu will be displayed. (menu 9-32)
3. Push the cursor key↑or↓to highlight the desired language.
4. PressENTERto select.
The OSD language changes to the selected language.
Installation
Input slots
File service
Internal pattern
When no signal
Source transition
OSD configuration
Language
V-Keystone
H-Keystone
Global keystone
Orientations
Back...

9. Installation menu
How to adjust the Vertical keystone ?
1. Push the cursor key↑or↓to highlightV-Keystone. (menu 9-33)
2. PressENTERto select.
A bar scale will be displayed.
3. Push the cursor key↑or↓to adjust the vertical keystone.
Adjust until the left and right vertical lines are straight.
Installation
Input slots
File service
Internal pattern
When no signal
Source transition
OSD configuration
Language
V-Keystone
H-Keystone
Global keystone
Orientations
Back
Menu 9-33
9.11 Horizontal keystone
What...

9. Installation menu
How to adjust the Horizontal keystone ?
1. Push the cursor key↑or↓to highlightH-Keystone. (menu 9-34)
2. PressENTERto select.
A bar scale will be displayed.
3. Push the cursor key↑or↓to adjust the horizontal keystone.
Adjust until the top and bottom horizontal lines are straight.
Installation
Input slots
File service
Internal pattern
When no signal
Source transition
OSD configuration
Language
V-Keystone
H-Keystone
Global keystone
Orientations
Back
Menu 9-34
9.12 Global keystone
What...

9. Installation menu
How to set up ?
1. Push the cursor key↑or↓to highlightOrientation. (menu 9-37)
2. PressENTERto select.
The orientation menu will be displayed. (menu 9-38)
3. PressENTERto toggle the orientation.
Possible orientations :
- Front/table : used when the projector is placed in front of the screen on a table.
- Front/ceiling : used when the projector is placed in front of the screen but mounted on the ceiling.
- Rear/table : used when the projector is placed behind the screen on a table.
-...

10. Service menus
10. SERVICE MENUS
Overview
• Service menu overview
• Start up the Service menu
• Identification screen
• Password
• IR address
• RS232 address
• Serial communication
• Thermal Diagnosis
• I2C Diagnosis
10.1 Service menu overview
Overview
• Identification
• Password
• IR address : 000
• RS232 address : 000
• Serial communication
• Thermal diagnosis
• I2C diagnosis
10.2 Start up the Service menu
The service menu can be password protected when the password protection is set to on.
How to...

10. Service menus
10.3 Identification screen
What can be seen on the identification screen?
The identification screen shows the general information of the projector.
The following items will be displayed:
• Type of projector: CineVERSUM 70
• IR address = address used for the remote control
• RS address = address used with RS232/422 serial communication
• Software version
• Baud rate: transfer speed for communication through RS232/RS422 with an external device or computer. The baud rate of the
projector...

10. Service menus
Enable/disable password
1. Push the cursor key↑or↓to highlightPassword. (menu 10-5)
2. PressENTERto select.
The password menu will be displayed. (menu 10-6)
3. Push the cursor key↑or↓to highlightUse password.
4. PressENTERto toggle betweenYe sorNo.
Yes Password is enabled
No Password is disabled. Free access to all menus.
Service
Identification
Password
IR address : 000
RS232 address : 000
Serial communication
Thermal diagnosis
I2C diagnosis
Back
Menu 10-5
Password
Use password : Yes...

10. Service menus
9. Enter in the same way.
10.PressENTERto accept this third character.
The new password is entered.
It becomes valid after a reboot of the projector. Switch off the projector and switch on again.
Service
Identification
Password
IR address : 000
RS232 address : 000
Serial communication
Thermal diagnosis
I2C diagnosis
Back
Menu 10-7
Password
Use password : Yes
Modify password
Back
Menu 10-8
Modify password
Enter new value :
0
Menu 10-9
10.5 IR address
Overview
An overview of the IR...

10. Service menus
How to setup
1. Push the cursor key↑or↓to highlightSerial Communication. (menu 10-11)
2. PressENTERto select.
The Serial communication menu will be displayed. (menu 10-12)
3. Push the cursor key↑or↓to highlightBaudrate PC.
4. PressENTERto toggle between the different possible baudrates.
The following baudrates are available :
- 1200
- 4800
- 9600
- 19200
Service
Identification
Password
IR address : 000
RS232 address : 000
Serial communication
Thermal diagnosis
I2C diagnosis
Back
Menu...

10. Service menus
How to set up ?
1. Push the cursor key↑or↓to highlightSerial Communication. (menu 10-13)
2. PressENTERto select.
The Serial communication menu will be displayed. (menu 10-14)
3. PressENTERto toggle betweenRS232andRS422.
Service
Identification
Password
IR address : 000
RS232 address : 000
Serial communication
Thermal diagnosis
I2C diagnosis
Back
Menu 10-13
Serial communication
Baudrate PC : 19200
Interface : RS232
Back
Menu 10-14
10.8 Thermal Diagnosis
About thermal diagnosis
This menu...