Barco Projector Cineversum 70 Quickstart Manual

3. Connections
3.4 S-Video input
Input location
ASPECT
RATIO
12V TRIGGERSCREENS-VIDEO VIDEO VHR/PrB/Pb
G/Y
Pr Pb Y
RS232/RS422
IN CONTROL
DVI INPUT
VGA INPUT COMPONENT VIDEO INPUT RGB/COMPONENT INPUT
Image 3-3
S-Video location
Pin configuration 4 pin connector
4
31
2
Image 3-4
For S-Video
pin 1 : earth (ground) luminance
pin 2 : earth (ground) chrominance
pin 3 : luminance signal (Y) 1Vpp ±3dB
pin 4 : chrominance signal (C) 300mVpp
Chrominance
The color component of a video signal that includes...

3. Connections
3.5 Composite Video input
Composite Video
Luminance and chrominance are combined along with the timing reference sync information using one of the cod-
ing standards--NTSC, PAL or SECAM--to make composite video. Most televisions and VCRs have composite video
connectors, which are usually colored yellow.
Input specifications and location
The composite video input is made of 1 RCA input terminal. Connect composite video signals from a VCR, OFF air signal decoder,
etc..
1.0Vpp ±3dB...

3. Connections
ASPECT
RATIO
12V TRIGGERSCREENS-VIDEO VIDEO VHR/PrB/Pb
G/Y
Pr Pb Y
RS232/RS422
IN CONTROL
DVI INPUT
VGA INPUT COMPONENT VIDEO INPUT RGB/COMPONENT INPUT
Image 3-6
5-cable input
Component Video
In Component Video the term component describes a number of elements that are needed to make up the video pic-
ture, these components are PR/Y/PB. A composite video signal on the other hand contains all the information needed
for the color picture in a single channel of information
Which signals can...

3. Connections
How to configure the 5-cable input ?
1. PressADJorENTERto open the Main menu. (menu 3-1)
2. Push the cursor key↑or↓to selectInstallationand pressENTER.
The installation menu will be displayed. (menu 3-2)
3. Push the cursor key↑or↓to selectInput slotsand pressENTER.
The input slots menu will be displayed. (menu 3-3)
4. Select 5 RCA and toggleENTERto switch betweenYUV,RGBandSCART.
SelectRGBfor the following source types:
-RGBHV
-RGBS
-RGsB
SelectYUVfor the following source types:
- Component...

3. Connections
3.8 Digital Visual Interface (DVI) input
DVI
Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays.
The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection
standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins
that handles both digital and analog video. This standard uses TMDS (Transition Minimized...

3. Connections
3.9 Computer input (RGB analog)
Input specification and location
TTL sync input : Umin=2.0V
RGB input = 0.7 V
pp±3dB
ASPECT
RATIO
12V TRIGGERSCREENS-VIDEO VIDEO VHR/PrB/Pb
G/Y
Pr Pb Y
RS232/RS422
IN CONTROL
DVI INPUT
VGA INPUT COMPONENT VIDEO INPUT RGB/COMPONENT INPUT
Image 3-9
Computer input
What can be connected ?
•RGBHV
•RG
SB
CompositesynconlypossibleonGreen
How to select a computer input ?
1. Press1on the RCU
Note:Another way of selecting the Computer (VGA) input is entering the Main...

3. Connections
Applications of the RS232/RS422 connection
Remote control:
• easy adjustment of projector via IBM PC (or compatible) or MAC connection.
• address range : 0 and 1.
• allow storage of multiple projector configurations and set ups.
• wide range of control possibilities.
Data communication: sending data to the projector or copying the data from the projector to the computer.
To set up the baud rate of the projector, see Baudrate setup, page 74.
3.11 Trigger outputs
Location
ASPECT
RATIO
12V...

3. Connections
24R5976763 CINEVERSUM 60/70 22042004 

4. Getting Started
4. GETTING STARTED
Overview
• Terminology overview
• Switching on
• Lamp runtime
• Switching from operational mode to standby
• Switching off the projector
• Temperature error DMD
•UsingtheRCU
• Projector Address
• Controlling the projector
4.1 Terminology overview
On projector
The controls are situated on the top cover of the projector.
1
2
3
4
Image 4-1
Ref.FunctionDescription
1Infra red receiverInfra red reception diode for IR signals coming from the Remote control
(RCU
2IR...

4. Getting Started
On Remote control
F2F3
F4
ADJ
EXIT
ENTER
PAUSETEXT
PHASE
TINT
COLOR
BRIGHTN
CONTR
VOL
90
78
56
3
4
12
*
SDI
SB-PC
DVI
VIDEO S-VIDEO
RGBPC
TREBLE
Balance
Bass
1
2
3
4
5
6
7
15
8
12
10 11 14
13
F1
F5
?
Sharpness
9
Image 4-2
Remote control
No.Key nameDescription
1RC operating indicationlights up when a button on the remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
2Function keysnot yet implemented
3ADJAdjust key, to enter or exit the...