Avaya Partner Advanced Communications System Installation, Programming And Use Manual

Installation
The 1600 DSL Module
2-23
Voice Gateway Configuration
Follow these steps to configure the voice gateway path:
1. Select “P. VoicePath Configure” from the Main Menu.
2. Select “V. Set Voice Gateway” from the Voice Configuration menu.
3. Select one of the following voice gateways according to your service provider from the Voice 
Gateway Selection menu:

1. CopperCom

2. MGCP 0.1/NCS 1.0 (PathStar)

3. Jetstream
4. Select “M. Manage MGCP/NCS Embedded Client” from the Main Menu.
5. Select “C....

PA R T N E R® Advanced Communications System Installation, Programming, and Use
The 1600 DSL Module
2-244. Do one of the following:

If you have the SDSL set for ATM, select the RFC 1483 port for the voice PVC (get this 
from the service provider).

If you have the SDSL set for Frame Relay, select the RFC 1490 port for the voice DLCI 
(get this from the service provider).
5. Type the IP address of the voice PVC/DLCI, and press Enter.
6. Press Esc to return to the Main Menu.
Router Configuration for Data...

Installation
The 012E Module
2-25 11. Type the gateway address given by the service provider at the “Enter Gateway address for 
Default Route” prompt, and press Enter.
12. Type “Y” at the “Save this as the default route in the static configuration?” prompt.
13. Press Esc to return to the Main Menu.
The 012E Module
Available in Release 5.0 or later systems, the 012E module provides 12 ETR extensions and no 
lines. All ports support full T/R capability along with ETR. The 012E module provides the...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
The 012E Module
2-26
Physical Design
The 012E module provides one power LED and 12 extension jack positions (see Figure 2-23). 
Consistent with all other PARTNER ACS modules, the extension jacks are labeled from the top 
down. The lowest extension number assigned to an 012E module occupies the jack position 
closest to the top of the module; the highest extension number occupies the jack position closest 
to the bottom of the...

Installation
Installing the Cover
2-27
Installing the Cover
Installing Telephones
After you have installed the control unit and have connected the line and extension cords, you are 
ready to install the telephones. Installing the telephones includes assembling, connecting, and 
testing the telephone. As desired, you also can connect an Intercom Autodialer to certain 
telephones.
Assembling PARTNER Telephones
All PARTNER telephones are shipped with a stand for either desk-mounting or wall-mounting the...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Installing Telephones
2-28
Desk-Mounting the Telephone
Follow these steps to desk-mount a telephone:
1. Gently place the telephone upside down.
2. Route the telephone cord through the hole in 
the top center of the stand (see Figure 2-25).
Figure 2-25. Routing the Telephone 
Cord
3. Insert the tabs on the narrow end of the stand 
into the slots on the inside bottom edge of the 
telephone (see Figure 2-26).
Figure 2-26....

Installation
Installing Telephones
2-29 4. While pressing in the tabs that protrude from 
the wide end of the stand, lower the stand to 
the telephone (see Figure 2-27).
5. Release the tabs to lock the stand into one of 
the three positions provided by the openings 
in the back of the telephone. The height of the 
stand is adjustable to three positions: low, 
medium, and high. The telephone height can 
be adjusted by moving the locking tabs to a 
different position.
6. Turn the telephone over.
Figure...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Installing Telephones
2-30
Wall-Mounting 
Follow these steps to wall-mount a PARTNER telephone:
1. Reverse the plastic hook that sits in the 
earpiece par t of the handset cradle 
(see Figure 2-29).
2. Turn the telephone upside down. If you have a 
tray on the bottom of your telephone, remove 
the tray that holds the User Instruction cards by 
pressing the tabs on both sides of the tray near 
the pull-out tab while sliding...

Installation
Installing Telephones
2-31 4. Plug one end of the telephone cord into the jack 
in the center of the wall plate (see Figure 2-31). 
5. Plug the other end of the telephone cord into 
the LINE jack on the bottom of the telephone.
6. Wrap any excess cord around the cord wrap 
posts on the bottom inside of the stand.
Figure 2-31. Plugging in the 
Telephone Cord
7. To mount the telephone onto the stand, insert 
the tabs on the top of the stand into the middle 
set of notches on the top edge of...

PA R T N E R® Advanced Communications System Installation, Programming, and Use
Installing Telephones
2-32
Connecting and Testing Telephones
9. Remove the plastic cover from the telephone 
(see Figure 2-33). Label the button sheet to 
show any programmed lines or button features. 
Then place the button sheet on the telephone 
so the holes fit over the buttons. Carefully 
replace the plastic cover.
10. Make sure the swivel display is set to the lowest 
position.
Figure 2-33. Removing the Plastic 
Cover...