ATT System 25 Advanced Administration User Guide

TABLE 16-29 Port/Board Type—Specific Representation (continued)
CATEGORY:
DESCRIPTION:
DATA:
Trunk
Ground Start, CO
701
Ground Start, WATS702
Loop Start, CO801
Loop Start, WATS802
PBX/Centrex805
DID Immediate Dial901
DID Wink Start902
Auto-in/Auto-out1001
Auto-in/Immediate Dial-out1002
Immediate Dial-in/Auto-out1003
Immediate Dial-in/Immediate Dial-out1004
Wink Dial-in/Auto-out
1005
Wink Dial-in/Wink Dial-out1006
Delay Dial-in/Auto-out
1007
Delay Dial-in/Delay Dial-out1008
Special
First Service...

TABLE 16-30 Save/Restore and System Restarts (Menu=9)
ACTION
For Action=1, you need to press the PLAY and RECORD buttons.
For Action=2 and Action=3, you need to press the PLAY button.
DESCRIPTIONDATA
1
Save (Backup) translations[1 to run]
2Verify translations[1 to run]
3Restore translations[1 to run]
10
Force a system warm start. FOR QUALIFIED[1 to run]
SYSTEMS TECHNICIAN ONLY
20
Force a system cold start. FOR QUALIFIED[1 for Full Default, 2
SYSTEMS TECHNICIAN ONLY. “Fullfor Limited Default]
Default”...

TABLE 16-32 Automatic Route Selection Administration (Menu=11) (continued)
ACTIONDESCRIPTIONDATA
100
Assign a pattern number[1-8]
101
Assign a start time for subpattern 1A in the form
[hhmm]
HOUR, MINUTES (HHMM)
102
Assign a stop time for subpattern 1A
[HHMM]
110
Assign Route 1 for subpattern 1A (a facility access[FAC or VFC]
code [FAC] or virtual facility code [VFC]
111Assign facility restriction level (FRL 0-3) for[FRL]
subpattern 1A, route 1
120Assign Route 2 for subpattern 1A (A facility access[FAC...

TABLE 16-32 Automatic Route Selection Administration (Menu=11) (continued)
ACTIONDESCRIPTIONDATA
401Assign the ARS access code[dial code: 9]
402Assign ARS pattern number for international calls[1-8; 0 for none; 0]
500Home Area Code (HAC) exception list number (1-4)[1-4]
501ARS routing pattern associated with[1-8]
this HAC exception list
511Display CO codes on this HAC
exception list (READ ONLY)
512Add CO code to HAC exception list[Code Number]
513Remove CO code from HAC exception list[Code Number]...

Requirements for the SAT
This section defines requirements for the System Administration Terminal (SAT). Any data
terminal with an RS-232C interface that meets the requirements below may be used as the
SAT.
Display
System 25 administration requires the following display characteristics:
n     Minimum display size of 16 lines by 80 columns
n     Ability to display upper case ASCII alphabetic characters, ASCII numeric, and some other
ASCII symbols (see “Keyboard” below)
n     Carriage return and line feed...

SAT Port Speed Setting
The data transfer rate for terminals or personal computers is set after a carriage return
character is entered from the device keyboard. Two data transfer rates are supported—1200
baud and 300 baud. The default rate is 1200 baud.
The following requirements apply to both the SMDR and administration ports:
n     Baud rate defaults to 1200 (can be set to 300)
n     No parity
n     One start bit, one stop bit, seven data bits
n     Data Terminal Ready (DTR) is required from printer
n...

Administering the T1 Carrier Interface (DS1)/HI D CKT
This section describes how to administer the System 25 optional DS1 interface, which provides
the means for connecting to a T1 carrier system.
The T1 carrier system for System 25 is a time division multiplexed, digital transmission system
for voice transmission. A DS1 interface installed on the System 25 can replace up to 24 off-
premises station (OPS) lines. Any combination of trunks (i.e., TIE, LS, GS, and OPS lines) that
does not exceed 24, can be...

TN746 Analog Line Circuit Pack Administration
This section describes the proper procedures for administering the DEFINITY TN746 circuit pack
within the System 25 R3V3 PBX.
The TN746 is a 16 port analog line circuit pack that has the functionality of both a ZTN78 (8 port
Tip/Ring line) circuit as well as a DEFINITY TN742 (8 port analog line) circuit pack. It is only
supported by the System 25 R3 software release. An 853B adapter, a two-leg splitter cable
labeled conn 0, conn 1 and conn 2, must be used...

High Density Circuit (HI D CKT) Administration
The action items in this section are used to administer certain hardware and DS1 circuit
parameters. All the actions in this section are organized under the HI D CKT Menu (Main Menu
item 3).
NOTE: Action item 6 cannot be changed with action item 2 set to enable.
Board Type
To specify a HID1     At 
Menu =, enter 3.
board type for a
particular slot before
installation:2     At 
Slot =, enter the CSS of the slot into which the HID
board will be installed.
3...