ATT System 25 Administration Manual

							To assign a toll
restriction class:1     At Action =, enter 14.
2     At 
Data =, enter the toll class number, 0 - 5, from the
following list:
O = Not toll restricted
1 = Toll Calls Allowed Lists 1-5
2 = Toll Calls Allowed Lists 2-5
3 = Toll Calls Allowed Lists 3-5
4 = Toll Calls Allowed List 4-5
5 = Toll Calls Allowed List 5 (only)
The default is 0.
NOTE: To allow restricted station to make operator-assisted
trunk calls, 
Action = 17, Data = 1 must be set for each trunk
used.
To assign an ARS Facility1     At Action =, enter 15.
Restriction level (FRL):
2     At 
Data =, enter the FRL number, 0 - 3, from the following
list:
LevelAllowed FRL Pools
O -
O
1 -0,1
2 -0,1,2
3 -0,1,2,3
The default is 3.
To assign the account1     At 
Action =, enter 21.
code entry type:
2     At Data =, enter:
- O for optional account code entry
- 1 for forced account code entry on all outside calls
- 2 for forced account code entry for calls that require
dialing a “0” or” 1“
The default is 0.
To allow toll-restricted1     At 
Action =, enter 23.
stations to make IXC
codes+1NPA calls:2     At 
Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is 0.
7-6 Administering Voice StationsNovember 1995 
						

							To allow toll-restricted
stations to make IXC
codes+011 calls:1     At Action =, enter 24.
2At Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is 0.
To allow toll-restricted
stations to make IXC
codes+NXX calls:1     At 
Action =, enter 25.
2At Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is 0.
November 1995Administering Voice Stations 7-6a 
						

							This page intentionally left blank.
7-6b Administering Voice StationsNovember 1995 
						

							Extended/Off-Premises
1     At Action =, enter 10.
Station: To make this
voice terminal an
extended station:2     At 
Data =, enter 1 for yes or 0 for no, based on
physical connection information.
Station Hunting: To
1     At 
Action =, enter 12.
administer this station to
hunt to another station if
busy:2     At 
Data =, enter the PDC of the station to hunt to next,
or 0 for none. The default is 0.
Coverage
To specify which receiver
group will cover this
station’s calls:1     At 
Action =, enter 7.
2     At 
Data =, specify which “receiver” group will answer
this station’s calls. Enter a coverage group number:
1 - 32: for a coverage group number
101 - 132: for a DGC coverage group number.
NOTE: This number actually
corresponds to a DGC group number
1-32 (the “1” in the hundreds’ place
indicates DGC coverage instead of
standard coverage).
0: for none. The default is 1.
To send ringing to the
1     At 
Action =, enter 8.
coverage station when
there is no answer at this2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1 @.
station:
@   Strongly recommended this value be used.
Administering Voice Stations 7-7 
						

							To send ringing to the
coverage station when
this station is busy:1     At Action =, enter 9.
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1 @.
Pickup: To assign this1     At 
Action =, enter 11.
station to a pickup group:
2     At 
Data =, enter the group number, 1-16, or 0 for
none. The default is 0.
Personal Speed Dialing:1     At 
Action =, enter 16.
To enable personal speed
dialing at this station:2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1 for single-line stations.
Forwarding: To allow1     At 
Action =, enter 22.
this station to send calls
2     At 
Data =, enter 1 for yes or 0 for no. The default is 0
to an outside location:
Callback Queuing
To assign the number of1     At 
Action =, enter 40.
times the system will
retry callback for an
internal facility:2     At 
Data =, enter the number of callback retries (after the
first try) for an internal facility, 0-15. The default is 2.
To assign the number of
rings per callback try for
an internal facility:1     At 
Action =, enter 41.
2     At 
Data =, enter the maximum number of times the
telephone should ring per callback try, 2 - 15.
The default is 3.
7-8 Administering Voice Stations 
						

							To assign the number of
1     At Action =, enter 42.
times the system will
retry callback for an
outgoing facility:2     At 
Data =, enter the number of callback retries (after the
first try) for an outgoing facility, 0 - 15. The default is 2.
To assign the number of
1     At 
Action =, enter 43.
rings per callback try for
2     At 
Data =, enter the maximum number of times the
an outgoing facility:
telephone should ring per callback try, 2 - 15.
The default is 3.
To enable automatic
1     At 
Action =, enter 44.
callback queuing for
2     At 
Data =, enter 1 for yes or 0 for no.
internal facilities:
The default is 0.
To enable automatic
1     At 
Action =, enter 45.
callback queuing for
2     At 
Data =, enter 1 for yes or 0 for no.
outgoing facilities:
The default is 1.
Call Waiting: to enable
call waiting for this
station:1     At 
Action =, enter 46.
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 0.
Administering Voice Stations 7-9 
						

							Night Service
To display the number of
each trunk assigned to
this station for Night
Service:1     At 
Action =, enter 51.
2     To continue the list, enter C after each trunk number is
printed.
To assign a trunk to this1     At 
Action =, enter 52.
station for Night Service:
2     At 
Data =, enter a 4-digit trunk number.
NOTE: Any given trunk can have no more than four Night
Service coverage stations assigned to it.
To delete a trunk from1     At 
Action =, enter 53.
this station’s Night
Service list:2     At 
Data =, enter a 4-digit trunk number.
7-10 Administering Voice Stations 
						

							Assigning Class-of-Service Options for Multiline
Voice Stations (Non-Attendant)
To assign COS to a1     From the Main Menu prompt, enter 2.
multiline voice station:
2     At 
PDC =, enter the PDC of the multiline voice station to
which you want to assign Class of Service.
Calling Restrictions
To restrict dial access to1     At 
Action =, enter 3.
the Central Office (CO)
trunk pool:2     At 
Data =, enter 1 for yes or 0 for no.
The default is 0.
To restrict dial access to1     At 
Action =, enter 4.
all other trunk pools:
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 0.
To restrict this station1     At 
Action =, enter 13.
from making any
2     At 
Data =, enter 1 for yes or 0 for no.
outward calls:
The default is 0.
To assign a toll1     At 
Action =, enter 14.
restriction class:
2     At 
Data =, enter the toll class number, 0 - 5, from the
following list:
O = Not toll restricted
1 = Toll Calls Allowed Lists 1-5
2 = Toll Calls Allowed Lists 2-5
3 = Toll Calls Allowed Lists 3-5
4 = Toll Calls Allowed List 4-5
5 = Toll Calls Allowed List 5 (only)
The default is 0.
NOTE: To allow Toll Restriction station to make operator-
assisted trunk calls, 
Action = 17, Data = 1 must be set for
each trunk used.
November 1995Administering Voice Stations 7-11 
						

							To allow toll-restricted
stations to make IXC
2codes+1NPA calls:1     At 
Action =, enter 23.
At 
Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is 0.
To allow toll-restricted1     At 
Action =, enter 24.
stations to make IXC
2At Data =, enter
codes+011 calls:
- 1 to allow calls
- O to disallow calls
The default is 0.
To allow toll-restricted1     At 
Action =, enter 25.
stations to make IXC
codes+NXX calls:
2At Data =, enter:
- 1 to allow calls
- O to disallow calls
The default is 0.
To assign an ARS Facility1     At 
Action =, enter 15.
Restriction level (FRL):
2     At 
Data =, enter the FRL number, 0 - 3, from the following
list:
LevelAllowed FRL Pools
O -0
1 -
0,1
2 -0,1,2
3 -0,1,2,3
To assign the account1     At 
Action =, enter 21.
code entry type:
2At Data =, enter:
- O for optional account code entry
- 1 for forced account code entry on all outside calls
- 2 for forced account code entry for calls that require
dialing a “0” or ”1“
The default is 0.
7-12 Administering Voice StationsNovember 1995 
						

							Line Preference
To assign ringing line
preference:
1     At Action =, enter 5.
2     At 
Data =, enter 1 for yes or 0 for no.
The default is 1 @.
To assign prime line1     At 
Action =, enter 6.
preference:2     At Data =, enter the button on which this line appears (the
preferred button number), or enter O for no line preference.
The default is 7.
(See the “Multiline Set Button Defaults” table under
“Administering Button Assignments”.)
@   Strongly recommended this value be used.
November 1995Administering Voice Stations 7-12a