ATT DEFINITY Communications System Generic 3, Installation, Administration, And Maintenance Of CallVisor, ASAI Instructions Manual

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
c. Plug the modem power cord into a wall outlet and power on the
modem.
d. Set the modem options. Refer to Appendix B, ``Supported
Terminals and Modems/Option Settings, for a list of option settings
for supported modems.
3. Connect a modem to the terminal.
a. If you are installing a new terminal, unpack it according to the
instructions supplied with the terminal.
b. Place the terminal on a suitable table and connect the keyboard.
c. Attach...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
If the terminal does not display the login prompt when the
DEFINITY LAN Gateway system is in one of the above states, try
pressing the 
Return key a few times. If the login prompt still does
not appear, write down the state displayed on the LCD, and then
see the troubleshooting procedure for terminal connections in
Appendix D (to be supplied).
k. Log in to the DEFINITY LAN Gateway system (see Chapter 3).  If
you can log in successfully, the...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
b. Plug the cable from the ADU into a telephone outlet.
2. In the terminal room, connect the Z3A-1 ADU to the terminal.
a. If you are installing a new terminal, unpack it according to the
instructions supplied with the terminal.
b. Place the terminal on a suitable table and connect the keyboard.
c. Attach the Z3A-1 ADU (male) to a serial RS-232 port on the
terminal (the DTE port on a 715 BCT).
NOTE:
If you connect the ADU to the DCE port on a...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbb
POWER
SUPPLY
GROUP 311
CABLE
SWITCH
ALARM
BOARD
MFB
Y-CABLE
ADMIN/
MAIN/
MULTI-
BOARD FUNCTIONALB
CABLE
(SEE
NOTE:  NULL MODEM IS REQUIRED WHENPORT B
PORT A
CONNECTING TO 715 BCT DCE PORT
7400A7400B
POWER
SUPPLY
NOTE)SITE-SPECIFIC
NETWORK
CONNECTIONS
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Figure 2-12.  Connecting a Terminal to the MFB via 7400 Data Sets
NOTE:
You may use two 7400A data sets in this configuration....

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
c. Connect the 4-pin connector on one of the 7400A power supplies to
the POWER connector on the data set, and plug the power supply
into a wall outlet.
d. Set the options and interface baud rate on the 7400A data set.
Refer to ``Using the Front Panel in the 
7400A Data Module Users
Manual, 
555-020-706, for details.
3. In the terminal room, connect the 7400B data set to the terminal.
a. If you are installing a new terminal, unpack it...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
j. Enter ATDT and the phone number of the 7400A data set
connected to the DEFINITY LAN Gateway system (refer to
Worksheet B-1, ``Terminals/Modems for this number).
After a connect interval, if the terminal and 7400 data sets are
installed correctly (and the system is in either OAM or OS state),
the screen displays the login prompt.
If the login prompt is not displayed when the system is in one of the
above states, try pressing the 
Return key...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
a. At the login prompt, type craft and press Return . (If the login
prompt is not displayed, press 
Return once or twice.)
NOTE:
To send the information to the DEFINITY LAN Gateway
system, the 
Return key (located on the right side of your
keyboard) must be pressed after you type a command or a
response to a prompt. On some keyboards, this key is
labeled 
Enter instead of Return . If your keyboard has both a
Return key and an Enter key (as on...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Initial Administrationbbbbbbbb
This section describes the tasks required to initially administer the DEFINITY
LAN Gateway system. It is expected that these procedures will be performed by
AT&T services personnel upon completion of the hardware installation.
Preliminary to installation, the Project Manager should complete the form located
in Appendix G.  After the system is installed, the Project Manager calls the TSC
to register the system....

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
change circuit-packs 1  Page 1 of 5
------------------------------------------------------------------------
CARRIER 1A
Slot Code  Name  Slot Code  Name
01: _____  11: _____ 
02: _____  12: _____ 
03: LGATE  RESERVED LGATE  13: _____ 
04: LGATE  RESERVED LGATE  14: _____ 
05: LGATE  RESERVED LGATE
06: TN2208  LAN GATE BOARD  * Use slots A01-A14 with
07: LGATE  RESERVED LGATE  * J58890G-1 control carrier.
08: _____  * Use slots A01-A10 with...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
The DEFINITY LAN Gateway logically occupies five slots on a port carrier.
The screen fields for these four or five slots are described as follows.
Board Number: Slot location in the switch.
Board Type: For the TN2208 circuit pack, ``LGATE BOARD is
displayed for the physical location of the board.  ``RESERVED
LGATE is displayed for the boards associated reserved (virtual)
slots.
Code: ``TN2208 is displayed for the slot on which it is...