ATT DEFINITY Communications System Generic 3, Installation, Administration, And Maintenance Of CallVisor, ASAI Instructions Manual

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Task 1: Verify the Selected Sitebbbbbbbbbbbbbbb
NOTE:
Defining the system requirements and ensuring that the site meets these
requirements are the responsibility of the Project Manager and the
customer and must be completed before you install the DEFINITY LAN
Gateway system. However, the guidelines are listed here so that you are
aware of these requirements.
Verify that the site selected for the DEFINITY switch and the DEFINITY LAN
Gateway...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Humidity range of 20% to 80%, noncondensing. In addition, make sure the
site is secure and provides protection from excessive sunlight, heat, cold,
chemicals, static electricity, magnetic fields, vibration, and grime.
NOTE:
ASAI must be enabled on the DEFINITY Customer Options form for the
system to be fully operational.
Task 2: Gather Required Toolsbbbbbbbbbbbbbbb
To install a DEFINITY LAN Gateway system, you need the following tools:
Narrow...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Task 4:  Verify Components and
Connectivity
bbbbbbbbbbbbbbb
Study Figure 2-2 that follows to gain a general understanding of how the system
assembly is to be connected.  Some customer-furnished LAN equipment is
included within the dotted lines in this figure.  Helpful definitions for this
equipment are as follows.
Balun (balanced/unbalanced) Ð An impedance matching transformer.
Baluns are small, passive devices that convert the impedance of...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbb
¶
BalunEthernet Coaxial Cable
(Twisted
Telnet Management
(Twisted Pair)
10BaseT
HUB
LAN
Server
Ñ Provided by AT&TRJ45
Software
Ñ Installed by customer
Ñ Maintained by customer
Ñ RJ45 connection
Ñ Located on cross-connect field
Ñ Maximum distance - 25 feet from switch
10BaseT
10BaseT
LAN
ServerALB
Cable
Alarm
Board(Not Used)
Switch
TN2170 RS-232Pair)
Modem Null Modem
T/R
House
Wiring
Z3A4 Z3A1Modem
Adapter
Power...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Refer to the diagrams in Tasks 6 and 7 in section 2 of this chapter, Hardware
Installation
, for additional connectivity details.  Then compare the parts listed in
Appendix C, ``Ordering Information with the actual parts you received to make
sure that all required parts have been ordered and shipped correctly.
NOTE:
The components listed in Appendix C are not the only equipment that can
be used with the DEFINITY LAN Gateway system.  Other...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Hardware Installationbbbbbbbb
This section describes the tasks needed to install the DEFINITY LAN Gateway
system hardware and peripheral hardware.
The DEFINITY LAN Gateway system installation tasks are the same for all
switch types. These tasks include:
Task 5:         Install the DEFINITY LAN Gateway system assembly
Task 6:         Connect the Alarm Board cables
Task 7:         Install the terminal (optional)
Task 8:         Connect the...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
For the same reason, do not cycle the power on the switch (for example,
during switch acceptance tests) once the system assembly is inserted
unless you have first shut down the DEFINITY LAN Gateway system. Refer
to the maintenance screens in Chapter 3 for the shutdown procedure.
Slot and Carrier Restrictions
If rearrangement of circuit packs in the PBX is required to accommodate the
system assembly, rearrange the packs as indicated on...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbb
Amphenol Connector
Female RJ45
Female
RS-232
MFB Y-Cable
(H600-352-G1)ALB Cable
(H600-353-G2)
20   19    18   17   16    15   14   13   12   11   10 5th   4th   3rd   2nd  1st
    9      8        7        6         5        4         3        2        1 Example of
DEFINITY LAN Gateway Slots
(not used)
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Figure 2-3.  Connecting the Adapter Cables Rear-Panel View
NOTE:
If the DEFINITY...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
NOTE:
You must connect these adapter cables directly to the port
connectors on the switch. If you install another cable between the
switch and the cables, the DEFINITY LAN Gateway system will not
operate correctly (either now or in the future).
a. Attach the male D-type amphenol connector on the Alarm Board
(ALB) cable (the one with two amphenol connectors, one RJ45
LAN connector, and one 25-pin RS-232 connector) to the ALB
(TN2170), the...

Installationbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbb
AT&T
ENTER
/ YES NEXT
/ NO BACK
I2C
bus cable
Power
cableSCSI
bus cable
Tie
wrap
Retaining
pins
Tape drive
(without cover)
SCSI
bus cable Disk
drive
Power
supply
Alarm board
(TN2170) Multi-Function board
(TN2208)
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Figure 2-4.  DEFINITY LAN Gateway System Assembly
!WARNING:
The DEFINITY LAN Gateway system will automatically boot when
seated in the slots.  Damage to the disk could...