ATT Definity Addendum 1 For Ds1, Dmi, Isdn Pri Instructions Manual

TIE TRUNK SETTINGSE-25
TABLE E-7 (continued). Trunk Group Screen Settings — Generic 1
FIELDSETTINGREMARKS
Max Message Size128128 bytes is the largest message a System 85 R2V4 can
To Sendreceive.
Connected tonoThis is a private network arrangement without connection to a
Toll?toll office.
Send SID?YAssign a y here if you want the calling partys station
number and/or connected partys number sent to a System 85
R2V4 on the far end.
The analogous System 85 R2V4 administration is in procedure
100, word 3,...

E-26TIE TRUNK SETTINGS
that routes the call. The Per Call SID/ANI field can be used to request SID/ANI only for specific
calls incoming on the group. The Night Serv field is used to have calls of different types routed to
different night destinations when night service is in effect.
This table is generally used when a Generic 1 is connected to the public network with several different
services (such as MEGACOM® 800 service and ACCUNET® Switched Digital Services) but also has
private network...

TIE TRUNK SETTINGSE-27
Routing Patter Screen Settings
This screen is used to build the routing patterns for ISDN-PRI calls made to a System 85 R2V4. The
patterns are selected using the HNPA, FNPA, RHNPA, and RNX tables. The only ISDN-PRI-specific
fields in this screen are the IXC, BCC value, and Service/Feature fields. The BCC value
fields can be used to route calls based on their ISDN BCs and low-layer compatibilities, such as voice
versus mode 1 digital data. The subnet trunking feature is also present...

E-28TIE TRUNK SETTINGS
TABLE E-9. Routing Pattern Screen Settings — Generic 1
FIELD
SETTINGREMARKS
IXCLeave this field blank for this application. 101288 is the
interexchange (long distance) carrier code for AT&T. Since
this is a private network, this field does not apply.
BCC ValueThis is where Generalized Route Selection (GRS) is
implemented.
If you want only certain types of calls to be routed to specific
trunk groups, enter a y for those types of calls in the desired
preference. Enter n for those...

TIE TRUNK SETTINGSE-29
SID PREFIX TABLE
ExtExtSIDExtExtSIDExtExtSID
LenCodePrefixLenCodePrefixLenCodePrefix
56561948566619495676194956861949
Figure E-13. SID PREFIX TABLE Screen
TABLE E-10. SID Prefix Table Screen Settings — Generic 1
FIELD
SETTING
REMARKS
Ext LenThis field and the next constitute a key that determines which
row of the table to apply to a call. Enter the number of
extension digits in the dial plan. For example, if you are on a
five digit dial plan, enter 5. You can also use this table...

E-30TIE TRUNK SETTINGS
TABLE E-10 (continued). SID Prefix Table Screen Settings — Generic 1
FIELD
SID Prefix
SETTINGREMARKS
Enter the digits you add to the extension code digits to form a
10-digit SID number. For example, in the sample screen
shown above, if any extension of the form 65XXX places or
answers a call, the number sent to a System 85 on the far end
will be 619-486-5XXX. In the example, the other numbers
that would be sent are 619-496-6XXX, 619-496-7XXX, 619-
496-8XXX.
Terminating Extension...

INDEX
011 calls C-1
1
1s density 1-17, 1-20
2
24th-channel signaling 1-14, 1-15, 2-3
4
4-wire E&M extended range channel units 2-5
5
50-pin (25-pair) connector configurations B-14
551V channel service unit 6-2
551V ST channel service unit 6-2
5ESS to another system 2-7
6
6500 IDSN Advantage 1-21
A
AAR assignments 7-46
access
ACCUNET 6-3, C-16
code
dial 7-26, 7-88
trunk 7-24, 7-86
connector, ISDN B-16
digital, and cross-connect system (DACS)
2-6, 5-6, B-12
equal 7-44, 7-47, 7-105, 7-108
ISDN 7-30
line...

IN-2INDEX
ANN11C/ANN11E feature comparison 6-2
APLT 7-34
area code 7-19
arithmetic logic unit (ALU) 4-3
ARS 2-6
ATMS
Generic 2 7-110
System 85 7-49
AT&T
ISDN
basic rate interface (BRI) 1-3
nodal services 1-31
primary rate interface (PRI) 1-3
proprietary signaling 1-14
reference frequency 2-7, 5-28
attendant partitions 7-20
Automatic Alternate Routing (AAR)
BC 1-25
called party IE 7-39
CBC 7-25, 7-31, 7-93
feature groups 7-4
feature parameters 7-108
ISDN dynamic trunk group C-6
network characteristics...

INDEXIN-3
cabling — Contd
CEM and CDM configurations 3-11
DS1 transmission 3-1
metallic 3-2
nonmetallic options 3-10
off-premises 3-9
on-premises 3-6
Call-by-Call Service Selection
advantages 1-30
description 1-29
Generic 1 services 7-127
ISDN public network connections 7-103
trunk type 120 7-25, 7-31, 7-87, 7-93
called party IE 1-29
calling line ID 1-34
calling number identifier 1-34
call-reference IE 1-29
call-reference value (CRV) 1-28
cancelers
echo 3-9
CAS 1-32
cascode node connections 5-24
CBC...

IN-4          INDEX
combination tie trunk 2-5, 6-4
common-channel signaling 1-23
Common-Control Switching Arrangement
(CCSA) 1-34
communication protocols 1-20
comparison — System 75 R1V2 versus
System 85/G2 7-113
compensation settings, line equalizer 3-13
composite clock output 5-16
conclusions on synchronization 5-29
connected number IE 1-32
connection, special access 2-6
connections using DS1/DMI terminal equipment
2-9
controlled slip 5-3
COR 7-120, 7-139, A-2
COS C-1
BC and ISDN routing 7-84...