AOR AR One Ultra Wide Band Reciever Instructions Manual

 50 
Alternatively, push the ESC key to abort entry.   
 
Or, push the down arrow key to move to the next item on the configuration menu (LAMP). 
 
6-2 Configure lamp 
The AR-ONE is equipped with high intensity green LEDs to illuminate the LCD and keypad   
when operating in areas of low level lighting. 
 
The lamp may be configured in three ways: 
 
AUTO    The lamp will automatically illuminate when the keypad or main tuning dial are   
used. 
The lamp will remain illuminated for further five second...

 51 
 
To access the configuration menu, push the FUNC key and then push the 7 key. 
 
Push the down arrow key to move the cursor to “DIMM” selection point.   
Use the main tuning dial or the right arrow key or the left arrow key to toggle the dimmer 
between ON and OFF.   
 
Push the ENT key to accept the data and return to a standard display.   
Alternatively, push the ESC key to abort entry.   
 
Or, push the down arrow key to move to the next item on the configuration menu 
(CONTRAST). 
 
6-4...

 52 
The manual AGC function is to adjust the receiver’s AGC (Automatic Gain Control) when it   
is set OFF.     
 
The default setting for Manual AGC is 255, maximum gain control value. 
The value can be adjusted according to the receiving condition. 
 
To access the configuration menu, push the FUNC key and then push the 7 key. 
 
Push the down arrow key to move the cursor to “MANU AGC” selection point.   
 
Use the main tuning dial or the right arrow key or the left arrow key to vary the manual AGC...

 53 
The IF gain control reduces the amplification in the receiver’s IF circuits and has the effect 
of  
reducing the sensitivity of the receiver. Normally, this is performed by the AGC system, and   
the control is left at maximum gain, but reducing the gain can be useful to limit noise when 
listening to CW or SSB signals. The IF gain control is must be used if the AGC is turned off. 
 
The default setting for IF-GAIN is 255, maximum gain control value. 
 
To access the configuration menu, push the...

 54 
Or, push the down arrow key to move to the next item on the configuration menu (BPS). 
 
6-8 Configure Remote BPS (Baud rate) 
The Remote BPS Set menu is used to configure the RS-232C computer control settings as 
it  
is important that they exactly match those of an associated computer connection or another   
AR-ONE (connected via a male 9-pin to mail 9-pin straight cable). 
 
To access the configuration menu, push the FUNC key and then push the 7 key. 
 
Push the down arrow key to move the cursor...

 55 
 
To access the configuration menu, push the FUNC key and then push the 7 key. 
 
Push the down arrow key to move the cursor to “RMT-ID” selection point.   
Use the main tuning dial or the right arrow key or the left arrow key to change the 
AR-ONE’s 
RS-232C identification address. 
 
Push the ENT key to accept the data and return to a standard display.   
Alternatively, push the ESC key to abort entry.   
 
Or, push the down arrow key to move to the next item on the configuration menu 
(DELAY)....

 56 
Use the main tuning dial or the right arrow key or the left arrow key to select the desired   
delay parameters. 
 
2.0s      The AR-ONE will wait the specified time after the squelch closes before   
resuming scan or search. 
HOLD    The AR-ONE will stop indefinitely when an active frequency is located, this   
is very useful when you don’t want to miss that once-in-a-lifetime   
transmission! 
OFF        The AR-ONE will resume scan or search instantaneously when the   
squelch closes. 
Push the...

 57 
(SPEAKER). 
 
6-12 Configure SPEAKER 
The AR-ONE is equipped with 2 separate speakers, one is in the main receiver unit and the 
another one is in the control head (Note: This function is available only when an optional 
separation kit is used), and a phones jack. Each speaker / head phones output can be 
configured under this menu. 
 
6-12-1 Configure rear speaker 
To access the configuration menu, push the FUNC
 key and then push the 7
 key. 
 
 
 
Push the down arrow key to move the cursor to...

 58 
To access the configuration menu, push the FUNC key and then push the 7 key. 
 
Push the down arrow key to move the cursor to “FRONT SP” selection point.   
This menu is to configure the front speaker.   
Use the main tuning dial or the right arrow key or the left arrow key to select the desired 
rear speaker setting (ON or OFF). 
 
Push the ENT key to accept the data and return to a standard display.   
Alternatively, push the ESC key to abort entry.   
 
Or, push the down arrow key to move to the...

 59 
There are four available pass frequencies:    50Hz, 200Hz, 300Hz, and 400Hz. 
 
The higher the frequency the more limited the audio bandwidth. For highest fidelity for 
listening, select 50Hz. The filter selection can be set to automode to select the proper filter 
setting automatically. 
 
The default is AUTO. 
 
To access the configuration menu, push the FUNC key and then push the 7 key. 
 
 
 
 
 
Push the down arrow key to move the cursor to “HPF” selection point.   
 
This menu is to configure...