AOR AR One Ultra Wide Band Reciever Instructions Manual

 30 
Examples are “000” for the first channel location in memory bank “0” and “099” for the last 
memory channel in memory bank “0”. 
 
“415” is the location: memory bank “4” channel “15”. 
 
The data contents of memory and search banks are held in a EEPROM so that no backup 
battery is required for memory retention. 
 
The stored data may be quickly and easily recalled, changed or deleted using the memory   
recall and delete functions. 
 
Note: 
When the receiver is switched OFF, all VFO data will be...

 31 
“3” location “25” (325) while in VFO mode with the text comment of    “AIRBAND”. 
If a mistake is made during programming, push the ESC key to abort entry and return to 
VFO mode. 
 
1)  Start by selecting VFO mode then key in the frequency of 123.500 MHz, “mode and 
step  
size” are set to the default auto mode.   
 
Push the VFO key to set the AR-ONE into VFO mode. 
Push the 1 key.   
Push the 2 key. 
Push the 3 key. 
Push the . (decimal) key. 
Push the 5 key. 
Push the ENT key. 
    
2)  Then...

 32 
 
 
 
3-3 Memory read “M.RD”  
Once frequency and mode data has been stored into a memory location, its retrieval is 
quick  
and simple.   
 
Let’s assume that you are going to retrieve the frequency of 123.500 MHz which has been   
programmed into memory “325” during an earlier example in the preceding section of this   
manual. 
 
Push the FUNC
 key and the push the SCAN
 key to go into memory read mode
, the 
“M.RD
”  
icon appears on the top left of the LCD to confirm operation. The AR-ONE will...

 33 
 
To recall memory channel “325”, push either the right arrow key or left arrow key to select 
“3” as the memory bank. Rotate the main tuning dial or pushing either the up arrow key or 
down arrow key to select “25”. 
 
3-4 Deleting memory channels 
It is possible to over-write a memory channel with new data or delete the channel entirely.   
Push the FUNC key, and then push the 3 key to “MEM DELETE” menu. 
 
Push either the right arrow key or left arrow key to select the desired memory bank....

 34 
 
SEARCH mode (covered later in this manual) automatically TUNES THE RECEIVER 
THROUGH ALL FREQUENCIES between two specified frequency limits looking for active 
frequencies. 
 
4-1 SCAN – outline introduction 
During SCAN, the AR-ONE automatically recalls memory channel which contains data in 
numeric order and monitors it looking for activity. When an ‘active’ memory channel is 
located (when a signal is found and the squelch is open), the AR-ONE will temporarily stop 
scanning. 
 
 
4-2 Starting...

 35 
To  e x i t  f r o m  SCAN mode, push the VFO key. 
 
4-4 Select scan 
Select scan enables you to ‘tag’ memory channels to make a temporary list up to 50   
channels in the same memory bank for scanning in a separate list called the SELECT 
SCAN 
LIST.  
 
4-4-1 Adding select scan channels in memory read 
In memory read mode, push the FUNC key, and then push the 1 key to toggle the select 
scan tag on/off, the icon “SEL” confirms selection. 
 
 
 
 
 
4-4-2 Starting / stopping select scan 
To start...

 36 
 
To stop select scan, push the VFO key. 
 
 
5    Search mode 
In search mode, the AR-ONE is programmed to automatically tune between two specified   
frequency limits looking for activity. Please refer to section 1-3 of this manual if you do not   
fully understand the function of SEARCH. 
 
5-1 Search type 
The AR-ONE is equipped with PROGRAM SEARCH. 
 
PROGRAM SEARCH = search between user preprogrammed limits 
 
5-1-1 Program search overview 
There are 40 program search banks (referred to simply...

 37 
zLO (lower) start frequency 
zHI (upper) stop frequency 
zReceive mode (or set to AUTO MODE) 
zText comment 
 
The program search banks are identified by numbers (01 ~ 40). To help with identification, 
each bank may be labeled with an alphanumeric text comment. 
 
5-2 Staring program search 
Presuming that data is already stored into a search bank … 
 
Push the SRCH
 key to start the program search process.   
 
 
The LCD icon “SRCH
” will be displayed and as long as the squelch is closed, the...

 38 
 
5-2-1 Reversing the direction of search 
To reverse the direction of search, use the main tuning dial or the up arrow key or the down 
arrow key. This is useful to enable you to search back over an interesting point of the 
search  
process. 
 
5-2-2 Forcing the search to resume 
If the AR-ONE stops on an unwanted busy frequency, rotate the main tuning dial knob or 
use the up arrow key or down arrow key to force the search process to resume from the 
current frequency displayed. 
 
5-2-3 Stopping...

 39 
 
 
5-4 Programming a search bank 
Each of the 40 search banks may be programmed with different frequency limits, receive   
modes, etc. as listed in section 8-1-1
 of this manual. 
 
Push the FUNC
 key, and then push the 6
 key to access the “SRCH PROG
” menu. 
 
 
 
Use the main tuning dial, or the right arrow key or the left arrow key or keypad to select the 
bank you wish to program or overwrite. (The down arrow key is used to move through the 
menu.