Anaheim Stepper DPD60401 Users Guide

SECTION 4FEATURES21 THUMBWHEEL SWITCH
To connect a SMC40M -TWS7seven decade thumbwheel switch, simply connect the cable that is included
into the expansion input slot on the Driver Pack. The SMC40M -TWS7 expansion module is used for
register  manipulation or math functions. (  Purchased Separately )
EXAMPLE 1:
Example 1 demonstrates the SMC40 reading the
first thumbwheel module(A) value dialed. If three
modules were in use, refer to them as A,B,C
where the furthest that is multidropped is C.
EXAMPLE 2:...

SECTION 4FEATURES22 Self TestDisabledEnabled-Disabled 

SECTION 5INSTALLATION23 SECTION 5 - INSTALLATION
UNIT SELECTION
Each SMC40 can be set to 1 of 10 possible unit numbers.  This can be changed by turning the unit
address switch to the appropriate position. Refer to Section 2, Figure 1 for location assistance.
BAUD RATE SELECTION
The Baud Rate is the transfer rate of the serial communications.  This is how fast the ASCII Data is sent
over the transfer lines.  The number specifies the number of bits that are sent per second.  With a baud
rate of 9600, 9600...

SECTION 5INSTALLATION24 DIMENSIONS - DRIVER PACKS
INDEXER TERMINAL BLOCK AND SWITCH LOCATION 

SECTION 5INSTALLATION25 DIMENSIONS – PCL402 & PCL403 

SECTION 5INSTALLATION26 DIMENSIONS - SMC40M - TWS7DIMENSIONS - SMC40M - 24I 

SECTION 5INSTALLATION27 AC POWER CONNECTION AND FUSE
The fuse is located in a panel underneath the 115 VAC line cord
socket.  See Section 9, on page 44 Specifications, for the
recommended part number.
HOOKUP FOR X250 VERSIONFigure 3 

SECTION 5INSTALLATION28 SINGLE AXIS INDEXER CONNECTIONS
Pin #Description1+5 VDC2Encoder X: Channel A3Encoder X: Channel B4Encoder X: Channel Z/Marker/Index50 VDC6X: Hard-7X: Soft8X: Home9X: Hard+100 VDC11X: CLK   (Available on PCL401 ONLY)12X: DIR   (Available on PCL401 ONLY)13X: PWR (Available on PCL401 ONLY)140 VDC   (Available on PCL401 ONLY)Table 6: Connector TB2 Pinout
Pin #DescriptionPin #Description1Input #1100 VDC2Input #211+5 VDC3Input #312Clamp4Input #413Output #250 VDC14Output #36Input...

SECTION 5INSTALLATION29 PCL INDEXER CONNECTIONS
 AXIS   X, Y, Z
Pin #Description1ISO +5 VDC2Encoder X: Channel A3Encoder X: Channel B4Encoder X: Channel Z/ Marker/ Index5ISO  0 VDC6X: Hard-7X: Soft8X: Home9X: Hard+10ISO  0 VDC11X: CLOCK  OUTPUT12X: DIRECTION OUTPUT13X: POWER (ON / OFF)14X: 0VDCPin #Description1ISO +5 VDC2Encoder Y: Channel A3Encoder Y: Channel B4Encoder Y: Channel Z/ Marker/ Index5ISO  0 VDC6Y: Hard-7Y: Soft8Y: Home9Y: Hard+10ISO  0 VDC11Y: CLOCK  OUTPUT12Y: DIRECTION OUTPUT13Y: POWER...

SECTION 5INSTALLATION30 2+5 VDC3+12 VDC UNREG49 – 12 VAC59 – 12 VACNOTE:  The ISO Power Connector is
different from the Power Connector. Both
sides of the PCL402 & PCL403 will need
power.
INDEXER INPUTS  (FLAT RIBBON HEADER)PIN #DescriptionPIN #DescriptionPIN #Description1Input 117Input 933Input 1720 VDC180 VDC340 VDC3Input 219Input 1035Input 1840 VDC200 VDC360 VDC5Input 321Input 1137Input 1960 VDC220 VDC380 VDC7Input 423Input 1239Input 2080 VDC240 VDC400 VDC9Input 525Input 1341Input 21100 VDC260 VDC420...