Home
>
Alpha Tool.Com.HK Limited
>
Cutting System
>
Alpha Tool.Com.HK Limited Stone Cutter AWS110220 User Manual
Alpha Tool.Com.HK Limited Stone Cutter AWS110220 User Manual
Here you can view all the pages of manual Alpha Tool.Com.HK Limited Stone Cutter AWS110220 User Manual. The Alpha Tool.Com.HK Limited manuals for Cutting System are available online for free. You can easily download all the documents as PDF.
Page 21
![Page 21
21
Note: If you notice any resistance while tightening the carbon brush cap, it is an indication
that the top plate on the carbon brush assembly is sticking inside the b\
rush cap.
Continuing to tighten will damage the carbon brush spring. (Go to step 6 to correct
this problem)
5. Tighten cap until secure as shown in
Figure 21
6. Remove the cap and carbon brush from the tool, visually check the two parts for
defects as shown in Figure 22.
Figure-21
Figure-22
Carbon Brush CapTop Plate](http://img.usermanuals.tech/thumb/326/5167/w300_stone-cutter-aws110220-user-manual-1478733721_d-20.png "Page 21
21
Note: If you notice any resistance while tightening the carbon brush cap, it is an indication
that the top plate on the carbon brush assembly is sticking inside the b\
rush cap.
Continuing to tighten will damage the carbon brush spring. (Go to step 6 to correct
this problem)
5. Tighten cap until secure as shown in
Figure 21
6. Remove the cap and carbon brush from the tool, visually check the two parts for
defects as shown in Figure 22.
Figure-21
Figure-22
Carbon Brush CapTop Plate")
21 Note: If you notice any resistance while tightening the carbon brush cap, it is an indication that the top plate on the carbon brush assembly is sticking inside the b\ rush cap. Continuing to tighten will damage the carbon brush spring. (Go to step 6 to correct this problem) 5. Tighten cap until secure as shown in Figure 21 6. Remove the cap and carbon brush from the tool, visually check the two parts for defects as shown in Figure 22. Figure-21 Figure-22 Carbon Brush CapTop Plate
Page 22
![Page 22
22
7. Check to see if the two parts move freely by pushing the top plate of th\
e carbon
brush into the recess on the bottom of the carbon brush cap and rotate.
Carbon Brush and Cap
Figure-23
Top Plate
8. If the two parts stick together, replace the carbon brush cap and repeat step 7.
9. If the top plate of the carbon brush sticks in the new cap, you need to \
replace the
carbon brush and repeat step 7.
10. Keep trying until carbon brush top plate can move freely inside of the r\
ecess on the...](http://img.usermanuals.tech/thumb/326/5167/w300_stone-cutter-aws110220-user-manual-1478733721_d-21.png "Page 22
22
7. Check to see if the two parts move freely by pushing the top plate of th\
e carbon
brush into the recess on the bottom of the carbon brush cap and rotate.
Carbon Brush and Cap
Figure-23
Top Plate
8. If the two parts stick together, replace the carbon brush cap and repeat step 7.
9. If the top plate of the carbon brush sticks in the new cap, you need to \
replace the
carbon brush and repeat step 7.
10. Keep trying until carbon brush top plate can move freely inside of the r\
ecess on the...")
22 7. Check to see if the two parts move freely by pushing the top plate of th\ e carbon brush into the recess on the bottom of the carbon brush cap and rotate. Carbon Brush and Cap Figure-23 Top Plate 8. If the two parts stick together, replace the carbon brush cap and repeat step 7. 9. If the top plate of the carbon brush sticks in the new cap, you need to \ replace the carbon brush and repeat step 7. 10. Keep trying until carbon brush top plate can move freely inside of the r\ ecess on the...
Page 23
23 RECOMMENDED ACCESSORIES This is the blade for cutting reinforced rod channels into granite or marble countertops. No longer is there a need to employ labor-intensive procedures for accomplishing this task. The 3” Hot-Rod cuts a ¼” groove in one easy pass. May be used wet or dry. Our premium wet saw blade: It is designed for cutting natural and engineered stone slabs and tile. The advanced style rim will cut most difficult natural and engineered stone tiles quickly and efficiently...
Page 24
24 ALPHA® AWS-110 WET STONE CUTTER SCHEMATIC AWS-110 / AWS-220
Page 25
25
ALPHA® AWS-110 WET STONE CUTTER PARTS LIST
DRAWING NO..PART NO.DESCRIPTIONQUANTITY
1133080Screw M5x403
2130031Self-tapping Screw 3.9×197
3133289/133292GFCI 110V/220V1
4133033Carbon Brush (2 pc set)4
5133031Brush Holder2
6133032Brush Cap2
7133241/133240Rated Plate 110V/220V1
8133047Cable Sleeve1
9130618Block Terminal2
10133040Wire Terminal2
11133042Insulation Pipe2
12133034Brush Terminal Assembly2
13133436/133004Field Coil 110V/220V1
14133086Cable Clamp1
15133055Cover1
16133030Air Bridge1...
Page 26
26 ALPHA® AWS-110 WET STONE CUTTER PARTS LIST DRAWING NO.PART NO.DESCRIPTIONPIECES 37133082Flange II (for AWS-110)1 38133464Screw M6×20-Left1 39133081Flange I (for AWS-110)1 40133062O Ring 18×2.51 41133057Spindle (for AWS-110)1 42133053Bearing 6201-2RS1 43133242Brand Poster1 44133266TT Ruler Guide (for AWS-110)1 45133058Gear (Big)1 46133066Needle Bearing BK 08101 47133255Gear Box1 48133067O Ring 25.5×21 49133084Wing Screw1 50133269Washer For Ruler1 51133085Pin 6×283 52133107Screw M3×51 53133108Lock...
Page 27
27 Optional: Alpha® Guide Rail and Clamp OPTIONAL: CARRIAGE ASSEMBLY SCHEMATIC PART NO. AWS-UCAM
Page 28
28 CARRIAGE ASSEMBLY PARTS LIST DRAWING NO.PART NO.DESCRIPTIONQUANTITY 1133285Screw cap M84 2133252Washer 9×16×1.64 3133383Guide Rail Carriage1 4133072Spring Lock Washer M65 5803138Screw cap M64 6133071Washer 69 7133251Screw M6×125 8133248Pressing plate5 9133560Screw M6×164 10130798E rings 58 11133246Caster4 12133245Caster axle4 13133384Stone Cutter Base1 14133238Rail wheel axle4 15133239Rail wheel4 16133051Circlips for shaft4
Page 29
29
EC DECLARATION OF CONFORMITY
Name of Manufacturer: Alpha Professional Tools®
Address of Manufacturer: 103 Bauer Drive
Oakland, NJ 07436
USA
Herewith declares that:
ELECTRIC HAND TOOL: “Electric Stone Cutter”
Make: Alpha Professional Tools®
Type: AWS-110/AWS-220
-Does comply with the provisions of the Low Voltage Directive 73/23EEC amended by
93/68 EEC and Machinery Directive 98/37/EC.
And furthermore declares that:
-The following (parts/clauses of) harmonized standards...
Page 30
30 SERVICES AND WARRANTY INFORMATION LOANER PROGRAM: Loaner tools can be issued to temporarily replace a tool that is being returned to Alpha® for repair. If more than one tool is being returned for repair, the number of loaner tools provided will be based on availability. If a loaner tool is required, contact the Tool Department at Alpha® at (800) 648-7229 to receive a Loaner Tool Application. A valid credit card number must be provided as a security deposit. The credit card will only be...