Alpha Tool.Com.HK Limited Stone Cutter AWS110220 User Manual

Part No: AWS-110 / AWS-220
103 Bauer Drive, Oakland NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com
Alpha® Wet Stone Cutter
Instruction Manual
MANUAL
®  

2
TABLE OF CONTENTS
Introduction ........................................................................\
........................................3
 About the Symbols ........................................................................\
....................3
 Electrical Symbols ........................................................................\
.....................3
Safety instructions ........................................................................\
............................4
 For...

3
INTRODUCTION
Thank you for purchasing the Alpha® AWS-110 Wet Stone Cutter  Please read this instruc-
tion manual thoroughly to ensure safe and correct use of the wet stone cutter.  Keep this 
manual in a place where operators can access it easily whenever necessar\
y.
 ABOUT THE SYMBOLS
According	to	the	 hazard	 level,	all	safety	 notes	in	this	 manual	 are	classified	 into	“DANGER”, 		
“WARNING”,	and	“CAUTION”.
    DANGER! Death or serious personal injury is imminent when handling this tool...

4
Note:   In some situations, failing to observe WARNING notes could result in   death or 
serious personal injury.  Be sure to read and observe the safety notes to ensure 
safe and correct use of the wet stone cutter.  
  CAUTION!
The following are important notes for products, operation, and maintenan\
ce applicable to 
this stone cutter.
 SAFETY INSTRUCTIONS  
Read all these instructions before attempting to operate this product.
  WARNING!
When using electric tools, basic safety precautions should...

5
10. Do not abuse the electrical cord
 Never carry the tool by the electrical cord or pull it to disconnect fro\
m receptacle.  Keep 
the electrical cord away from heat, oil and sharp edges.
11. Secure workpiece
 Use clamps or a vise to hold workpiece rather than using your hands.
12. Do not overreach
 Keep proper footing and balance at all times. 
13. Maintain tools with care
 Keep tools sharp and clean for better and safer performance. Follow inst\
ructions for 
lubricating and changing accessories....

6
AWS-110 OVERVIEW
  SPECIFICATIONS
Rating ................................................................................................110/220 Volts
Amperage ...................................................................................................11.2/5.5
Power .....................................................................................................\
......1200W
No-load Speed ........................................................................\
............13,000 RPM
Weight...

7
 ACCESSORIES
COMPONENTS: 
1. Ground Fault Circuit Interrupter (Part No. 133289/133292)
2. Water Valve (Part No. 133362)
3. Water Attachment Assembly (Part No. 133287)
4. Spanner Wrench M 22  (Part No. 133097)
5. TT Ruler Guide (reversible) (Part No. 133266)
6. T-Handle Wrench  (Part No. 133098)
7. Extra Carbon Brush (2 pc set)  (Part No. 133033)
8. Self-stick Felt Strip Set (Part No. 133369)






Figure-2   

8
ADDITIONAL PRECAUTIONS FOR USING  
THE WET STONE CUTTER
In addition to the general safety notes described on the preceding pages, please read 
and observe the following precautionary notes before using the wet stone\
 cutter.
  DANGER!
 INSTRUCTIONS
Alpha Professional Tools®	provides	 the	highest	 quality	parts	and	manufacturing	 techniques	
in the manufacture of this tool. In order to obtain the maximum effectiv\
eness and provide 
the highest degree of safety, it is necessary to review and follow...

9
•	 Always	use	and	 store	 the	saw	 blades	 according	 to	the	 manufacturer’s	 instructions.	
The	flange	bolt	must	be	tightened	before	starting	to	work	with	the	machine.
•	 The	work	piece	 must	be	secured	 if	it	is	 not	 heavy	 enough	 to	prevent	 movement.
•	 Do	not	use	emery	wheel.
•	 The	tool	is	designed	for	cutting	on	horizontal	surfaces.
USAGE
This wet stone cutter can be used for cutting many different materials, e.g. tile, concrete, 
stone or glass. In case of doubt please read the manufacturer’s...

10
 GROUND FAULT CIRCUIT INTERRUPTER: 
  DANGER!
 Do not bypass the GFCI if this condition occurs, a real shock hazard may\
 exist.
 WARNING!
If the GFCI fails to trip when the test button is pressed, or fails to r\
eset, the device is 
defective and should be replaced.
If the GFCI tests properly without a load applied, but trips each time a load is connected, 
then the load (tool) has a ground fault condition and needs to be repa\
ired or replaced.  
Do not bypass the GFCI if this condition occurs, a...