A&D Scale SFSG Series User Manual

SF/SG Series Operating Instructions10 11. Clear Entry FunctionM+CEtotal          3        55.00         WEIGHTUNIT PRICEPRICEtotal         2   45.00    WEIGHTUNIT PRICEPRICE TOTAL  M+TOTAL  M+XC
Press                  to cancel this operation.MODE(
(PC         0.00  00.00 WEIGHTUNIT PRICEPRICE
entries.10. Calculating the Correct Change
The purpose of this function is to allow the operator to determine the correct change to return to the
customer once payment has been made.
Example: There have been 4...

SF/SG Series Operating Instructions12. Automatic Cancellation of a Unit Price
In very busy applications, it may be more convenient for the Unit Price entry to return to zero after each
operation.
To do this, press                         while the display is in normal operation.
                                                                             Automatically clears the unit price.
                                                                             Does not automatically clears the unit...

SF/SG Series Operating InstructionsF1: Auto display off0: Yes1: No
F2: Cancellation of unit price0: Selectable1: No                     2: Yes
F3: Output Data0: Key trigger mode 11: Key trigger mode 2
      (Refer to the note below.)2: Command mode3: Stream mode
4: Key trigger mode 3 with delay
5: Key trigger  mode 3 without delay
6: Not used 7: Not used
8: Label printer mode
F4: Baud Rate0: 600 bps1: 1200 bps
2: 2400 bps3: 4800 bps           4: 9600 bps
F5: Parity Bit0: 7 bits (Even)1: 8 bits (No...

130 SF/SG Series Operating Instructions14. Connecting the Scale to the AD-8124 Label Printer
14-1 Confirming the SF/SG Program Version
Confirm the SF/SG program version as follows:
Step 1:While holding down the ZERO key (            ) of the numerical keypad , turn the power switch
on.
Step 2:When “888888 ” appears, the scale program version is earlier than 4.00. When “rP XXX ”
appears, the scale program version is 4.00 or later.
               Earlier than 4.00                   4.00 or laterNote about...

14 SF/SG Series Operating Instructions14-3 Setting the printer internal clock
Set the printer internal clock as follows:
Example:Set the clock to 9:45, June 10, 2001.
Step 1:While holding down                        , turn the scale’s power switch on. All the displays 
indicate “- - - - - - -” as shown below:
Assure that the printer power switch is turned on.
Step 2:Enter the date and time using the numerical keypad. Enter 4 digits for the year, 2 digits for the
month, 2 digits for the day, 2 digits for...

15 SF/SG Series Operating InstructionsStep 6: Press the PLU 2 key. The data will be sent to the printer and the scale will return to the normal
weighing mode. If the scale will not return to the normal weighing mode, check the values 
entered.
Step 7: Using the numerical keypad, enter “1”, “0”, “0”, “6”, “2”, “0”, “0”, “1”, “0”, “9”, “4” and “5” in
 this order. If an error is made, press          to clear the values. And re-enter the values.
        SF series       SG series
Step 8: Press the PLU 3 key....

SF/SG Series Operating Instructions16Step 2: Using the numerical keypad, enter a 3-digit label number. If an error is made, press          to clear
 the values. And re-enter the values.
        SF series       SG series
Step 3: Press the PLU key to assign to the label number, in this example, the PLU 5 key. . The PLU 
number will be sent to the printer and the scale will return to the displays described in step 1. If the
label number is “000 ”, it will not be sent to the printer.
Step 4: Repeat steps 1...