2012 Na Yamaha Super Tenere Manual

haha GENERATOR AND STARTER CLUTCH5-46
3. Apply:Sealant
(onto the stator coil lead grommet)
4. Install: Generator cover gasket 
 Generator cover
TIP
Tighten the generator cover bolts in stages and 
in a crisscross pattern.
5. Connect:
Stator coil coupler
TIP
To route the stator coil lead, refer to  “CABLE 
ROUTING ” on page 2-43.
  Yamaha bond No. 1215
90890-85505
(Three Bond No.1215®)
T R..  Generator cover bolt (M6 
× 55)
12 Nm (1.2 m· kgf, 8.7 ft·lbf)
LOCTITE ®
Generator cover bolt (M6  × 25)
12...

haha ELECTRIC STARTER
5-47
EAS24780
ELECTRIC STARTER Removing the starter motor
Order Job/Parts to remove Q ’ty Remarks
Fuel tank Refer to “FUEL TANK ” on page 7-1.
1 Starter motor lead 1 Disconnect.
2 Starter motor assembly 1
For installation, reverse the removal proce-
dure.
1
2
12 Nm (1.2 m

kgf, 8.7 ft 
Ibf)T.R.
5 Nm (0.5 m 
kgf, 3.6 ft 
Ibf)T.R.
NewLS  

haha ELECTRIC STARTER
5-48
Disassembling the starter motor Order Job/Parts to remove Q ’ty Remarks
1 Starter motor front cover 1
2 Starter motor rear cover 1
3 Brush holder set 1
4 Armature assembly 1
5 Starter motor yoke 1
For assembly, reverse the disassembly pro-
cedure.
1
4
2
3 (4)
5
5 Nm (0.5 m

kgf, 3.6 ft 
Ibf)T.R.
11 Nm (1.1 m 
kgf, 8.0 ft 
Ibf)T.R.
New
New  

haha ELECTRIC STARTER
5-49
EAS24790
CHECKING THE STARTER MOTOR
1. Check: Commutator
Dirt   Clean with 600 grit sandpaper.
2. Measure:
Mica undercut  “a”
Out of specification   Cut the mica to the 
proper measurement with a hacksaw blade 
that has been grounded to fit the commutator.
TIP
The mica of the commutator must be undercut to 
ensure proper operation of the commutator.
3. Measure: Armature assembly resistances (commutator 
and insulation)
Out of specification   Replace the starter 
motor.
▼▼▼▼...

haha ELECTRIC STARTER
5-50
7. Check: Bearing
 Oil seal
Damage/wear   Replace the starter motor 
front cover.
EAS24800
ASSEMBLING THE STARTER MOTOR
1. Install: Starter motor yoke “1”
 Starter motor front cover  “2”
 Starter motor rear cover  “3”
TIP
Align the match marks “a”  on the starter motor 
yoke with the match marks  “b” on the starter mo-
tor front and rear covers.
a
a
bb
213  

haha CLUTCH
5-51
EAS25061
CLUTCH Removing the clutch cover
Order Job/Parts to remove Q ’ty Remarks
Engine oil Drain.
Refer to 
“CHANGING THE ENGINE OIL ” on 
page 3-24.
1 Engine oil filler cap 1
2 Crankshaft end accessing screw 1
3 Clutch cover 1
4 Clutch cover gasket 1
5 Dowel pin 2
6 Clutch cover damper plate 1
7 Clutch cover damper 1
For installation, reverse the removal proce-
dure.
2
3 (14)
1
NewNew
New
10 Nm (1.0 m

kgf, 7.2 ft 
Ibf)T.R.
12 Nm (1.2 m 
kgf, 8.7 ft 
Ibf)T.R.
12 Nm (1.2 m 
kgf,...

haha CLUTCH
5-52
Removing the clutch Order Job/Parts to remove Q ’ty Remarks
Clutch release cylinder Refer to 
“Removing the clutch release cylin-
der ”.
1 Clutch spring plate retainer 1
2 Clutch spring plate 1
3 Clutch spring plate seat 1
4 Pressure plate 1
5 Bearing 1
6 Short clutch push rod 1
7Ball 1
8 Long clutch push rod 1
9 Friction plate 1 1 Inside diameter: 124 mm (4.88 in)
10 Clutch plate 7
11 Friction plate 2 7 Inside diameter: 124 mm (4.88 in)
8 Nm (0.8 m
kgf, 5.8 ft 
Ibf)T.R.
125 Nm (12.5...

haha CLUTCH
5-53
Removing the clutch Order Job/Parts to remove Q ’ty Remarks
12 Clutch boss nut 1
13 Conical spring washer 1
14 Wire circlip 1
15 Clutch plate 1
16 Friction plate 3 1 Inside diameter: 135 mm (5.31 in)
17 Clutch damper spring 1
18 Clutch damper spring seat 1
19 Clutch boss 1
20 Thrust washer 1
21 Clutch housing 1
22 Spacer 1
23 Bearing 1
8 Nm (0.8 m
kgf, 5.8 ft 
Ibf)T.R.
125 Nm (12.5 m 
kgf, 90 ft 
lbf)T.R.New
New
NewE
E
E
E
E
LS
LS
E
14
12
15
16
17
21
18
19
202223
13
16
(6)  

haha CLUTCH
5-54
Removing the clutch Order Job/Parts to remove Q ’ty Remarks
24 Spacer 1
25 Thrust plate 1
For installation, reverse the removal proce-
dure.
8 Nm (0.8 m 
kgf, 5.8 ft 
Ibf)T.R.
125 Nm (12.5 m 
kgf, 90 ft 
lbf)T.R.New
E
E
E
E
E
LS
LS
E
2425
(6)  

haha CLUTCH
5-55
Removing the clutch master cylinder Order Job/Parts to remove Q ’ty Remarks
Clutch fluid Drain.
Refer to 
“BLEEDING THE HYDRAULIC 
CLUTCH SYSTEM ” on page 3-12.
1 Hand shield 1
2 Grip end 1
3 Rear view mirror 1
4 Upper hand shield bracket 1
5 Clutch master cylinder reservoir cap 1
6 Clutch master cylinder reservoir diaphragm 
holder 1
7 Clutch master cylinder reservoir diaphragm 1
8 Lower hand shield bracket 1
9 Clutch lever 1
10 Bushing 1
3
10
5
6
7
9
8 2
1
4
SNewNew
LT
1.0 Nm (0.10 m...