2012 Na Yamaha Super Tenere Manual

haha SHAFT DRIVE
4-118
8. Install: Rear wheel
Refer to  “REAR WHEEL ” on page 4-29.
9. Fill: Final gear case
Refer to  “CHECKING THE FINAL GEAR OIL 
LEVEL ” on page 3-28.  

haha SHAFT DRIVE
4-119  

haha 5
ENGINE
ENGINE INSPECTION .................................................................................... 5-1
MEASURING THE COMPRESSION PRESSURE .................................... 5-1
ENGINE REMOVAL ........................................................................................ 5-3
REMOVING THE ENGINE ........................................................................ 5-9
INSTALLING THE ENGINE....................................................................... 5-9...

haha ELECTRIC STARTER................................................................................... 5-47
CHECKING THE STARTER MOTOR ..................................................... 5-49
ASSEMBLING THE STARTER MOTOR ................................................. 5-50
CLUTCH ........................................................................................................ 5-51
REMOVING THE CLUTCH ..................................................................... 5-59
CHECKING THE...

haha CRANKCASE................................................................................................ 5-81
REMOVING THE REAR BALANCER ..................................................... 5-86
DISASSEMBLING THE CRANKCASE.................................................... 5-86
CHECKING THE CRANKCASE .............................................................. 5-87
CHECKING THE REAR BALANCER ...................................................... 5-87
CHECKING THE TIMING CHAIN AND TIMING CHAIN...

haha ENGINE INSPECTION
5-1
EAS23P1087
ENGINE INSPECTION
EAS20710
MEASURING THE COMPRESSION 
PRESSURE
The following procedure applies to all of the cyl-
inders.
TIP
Insufficient compression pressure will result in a 
loss of performance.
1. Measure: Valve clearance
Out of specification   Adjust.
Refer to  “ADJUSTING THE VALVE CLEAR-
ANCE”  on page 3-5.
2. Start the engine, warm it up for several min-
utes, and then turn it off.
3. Remove: Air filter case
Refer to  “GENERAL CHASSIS ” on page 4-1.
4....

haha ENGINE INSPECTION
5-2
Refer to the following table.
▲▲▲▲ ▲ ▲▲▲ ▲▲▲▲▲ ▲ ▲ ▲▲▲▲ ▲ ▲▲▲▲ ▲ ▲▲▲ ▲▲▲▲
9. Install: Spark plug
10.Install: Ignition coil
11.Connect: Ignition coil couplers
12.Install: Air filter case
Refer to  “GENERAL CHASSIS ” on page 4-1.
Compression pressure (with oil applied into 
the cylinder)
Reading
Diagnosis
Higher than without 
oil Piston ring(s) wear or 
damage 
 Repair.
Same as without oil Pistons, valves, cylin-
der head gasket or 
piston ring(s) possi-
bly defective 
 Re-...

haha ENGINE REMOVAL
5-3
EAS23711
ENGINE REMOVAL Removing the exhaust pipe
Order Job/Parts to remove Q ’ty Remarks
Right side cowling/Engine guard Refer to 
“GENERAL CHASSIS ” on page 
4-1.
1Muffler  cover 1
2 Left passenger footrest 1
3 Muffler protector 1
4 Exhaust pipe joint bolt 1
5 Rubber cover 1
6Muffler 1
7Collar 1
8 Rubber damper 1
9Gasket 1
10 O
2 sensor #1 coupler
1
 Disconnect.
10
4
95
8
6
1
32
7
(4)
New
LT
7 Nm (0.7 m 
kgf, 5.1 ft 
Ibf)T.R.
7 Nm (0.7 m 
kgf, 5.1 ft 
Ibf)T.R.
8 Nm (0.8 m...

haha ENGINE REMOVAL
5-4
Removing the exhaust pipe Order Job/Parts to remove Q ’ty Remarks
11 O
2 sensor #2 coupler
1
 Disconnect.
12 Exhaust pipe protector 1
13 Exhaust pipe 1
14 Gasket 2
For installation, reverse the removal proce-
dure.
11
12 13
14
(4)
New
LT
7 Nm (0.7 m

kgf, 5.1 ft 
Ibf)T.R.
7 Nm (0.7 m 
kgf, 5.1 ft 
Ibf)T.R.
8 Nm (0.8 m 
kgf, 5.8 ft 
Ibf)T.R.
20 Nm (2.0 m 
kgf, 14 ft 
Ibf)T.R.
20 Nm (2.0 m 
kgf, 14 ft 
Ibf)T.R.
20 Nm (2.0 m 
kgf, 14 ft 
Ibf)T.R.
28 Nm (2.8 m 
kgf, 20...

haha ENGINE REMOVAL
5-5
Disconnecting the leads Order Job/Parts to remove Q ’ty Remarks
Engine oil Drain.
Refer to 
“CHANGING THE ENGINE OIL ” on 
page 3-24.
Drive shaft Refer to “SHAFT DRIVE ” on page 4-103.
Clutch hose Disconnect.
Refer to 
“CLUTCH ” on page 5-51.
Shift arm Refer to “SHIFT SHAFT”  on page 5-71.
Radiator Refer to “RADIATOR ” on page 6-1.
Thermostat Refer to “THERMOSTAT ” on page 6-4.
Radiator outlet pipe Refer to “WAT ER  P UM P ” on page 6-6.
Canister Refer to 
“FUEL TANK ” on page...