Yamaha Cl 5 User Guide

Input channels
 Reference Manual
31
1
Channel select button
Indicates the channel icon, number, and name. When you press this button, the 
corresponding channel will become a target  for operations in the SELECTED CHANNEL 
section, and the corresponding [SEL] key will light.
2
PATCH button
Press this button to display the PORT SELECT window to patch the input port to the 
input channel.
PORT SELECT window
• TAKE FROM PORT button The HA settings of the port will take priority . Even if you change the...

Input channels
 Reference Manual
32
GAIN/PATCH window
(1-48, 49-72/ST IN (CL5), 49-64/ST IN (CL3), ST IN (CL1))This window displays the head amp settings of the corresponding input channels. Here you 
can also adjust the head amp gain in groups of the selected eight channels by using the 
multifunction knobs in the Centralogic section.1
Parameter select buttons
Switch parameters to view in the window.
• ANALOG GAIN ...................... Analog gain
• DIGITAL GAIN ....................... Digital gain
•...

Input channels
 Reference Manual
33
Relationship between analog  and digital gain while Gain 
Compensation is onIf Gain Compensation is on, adjusting the analog  gain by a specific amount will cause the I/O 
device to output to the audio network a signal that is attenuated by the same amount. 
Therefore, the signals on the audio network will maintain a constant corrected level in the 
digital domain.
For example, assume that the analog gain value has been set to +30 dB and Gain 
Compensation is now...

Input channels
 Reference Manual
34
TO STEREO/MONO window (8ch)Here you can control the on/off and pan/balanc e settings of the signal sent from input 
channels to the STEREO (L/R) bus and MONO (C) bus, in groups of eight channels.1
Channel select button
Selects the channel. You can select multiple channels simultaneously.
2
Mode LEDs
The LED of the currently- selected mode will light.
3
MODE select button
For a MONO channel, the mode can be sw itched between ST/MONO and LCR. For a 
STEREO channel, the...

Input channels
 Reference Manual
35
6
TO ST PAN/TO ST BALANCE knob
For MONO channels, this acts as a PAN knob  that adjusts the left/right panning of 
signals sent to the STEREO bu s. For STEREO channels, this acts as a PAN knob, and also 
as a BALANCE knob that adjusts the volume  of the left and right signals sent to the 
STEREO bus. To adjust the  value, press the knob to sele ct it, and then operate the 
corresponding multifunction knob.
7
Ta b s
Enable you to switch between windows.
8
LCR button
If...

Input channels
 Reference Manual
36
Signal level when  LCR mode is selectedIf LCR mode is selected, the signal level sent to the STEREO (L/R) bus and MONO (C) bus 
will vary according to the settings of  the CSR knob and the TO ST PAN knob.When the CSR knob is set to 0% (MONO channel)
The TO ST PAN knob operates  as a conventional PAN knob, and no signal is sent to the 
MONO (C) bus.
 When the CSR knob is set to 0% (STEREO channel)
The TO ST BALANCE knob oper ates as a conventional BALANCE knob, and no...

Input channels
 Reference Manual
37
Sending a signal from an input channel to a MIX/
MATRIX busThe MIX buses are used mainly for the purpose of sending signals to foldback speakers on 
stage, or to external effect processors. The MA TRIX buses are used to produce a mix that is 
independent of the STEREO bus or MIX buses, and is typically sent to a master recorder or 
to a backstage monitoring system.
You can send a signal from an input channel to a MIX/MATRIX bus in the following three ways. Using the...

Input channels
 Reference Manual
38
 If the MIX/MATRIX bus is a stereo bus
You can link the main parameters of tw o adjacent odd/even-numbered MIX/MATRIX 
buses. If the send-destination MIX/MATRIX bus is  assigned as stereo, the left knob of the 
two adjacent TO MIX/MATRIX SEND LEVEL kn obs will operate as the TO MIX/MATRIX 
PAN knob. (If BALANCE mode is selected in the TO STEREO/MONO window, it will 
operate as a BALANCE knob).
NOTE• For a MONO channel, the right knob will adjus t the common send level...

Input channels
 Reference Manual
39
4
Send destination select buttons
Select MIX/MATRIX buses as the send destination.
5
Channel select button
Selects the send-source channel that you wish to control. The current channel icon, 
number, and color appear on the button, and the channel name appears below the 
button.
6
PRE/POST button
Switches the send point of each send-sou rce channel between PRE and POST. If the 
button is lit, the send point is set to PRE.
NOTE• If the PRE/POST button is on, you can...

Input channels
 Reference Manual
40
• You can assign the SENDS ON FADER function to  a USER DEFINED key. This lets you quickly 
switch to SENDS ON FADER mode for a specif ic MIX/MATRIX bus, and quickly switch back 
again.
SENDS ON FADER mode1
MIX/MTRX ON FADER switch button
Use this button to switch between  MIX 1-16 and MIX 17-24/MATRIX for the bus 
displayed in the Function Access Area.
2
MIX/MATRIX bus select buttons
Select the buses that will  be controlled by the faders.
3
Close button
Closes the...