Yamaha Cl 5 User Guide

SELECTED CHANNEL section
 Reference Manual
11
FADER fieldThis field enables you to make settings for the channel on/off 
status and the level.1
Fader
Displays the current level.
Use the faders on the top panel to set the levels.
2
Level indicator
Displays the current level setting by numerical value. If 
the signal is clipping at any point in the channel, the Σ CLIP indicator will light.
3
ON button
Switches the channel on and off. The button is linked with the corresponding [ON] key 
on the top panel....

Centralogic section
 Reference Manual
12
Centralogic sectionThe Centralogic section located below the touch screen lets you recall and simultaneously 
control a set of eight input channels, output channels, or DCA groups. If you press one of the 
Bank Select keys, the channels or DCA groups corresponding to that key will be assigned to 
the Centralogic section, and can be controlled using the faders, [ON] keys, and [CUE] keys in 
the Centralogic section.
Operations in the Centralogic section
NOTE• When...

Centralogic section
 Reference Manual
13
OVERVIEW ScreenCHANNEL NAME fieldThis field appears at the top and bottom of the screen and displays the channel number, 
name, and icon for the currently-selected eight channels. The name of the currently-selected 
channel is highlighted.
NOTE
If you have retained a specific channel (that is controlled by the faders or knobs in the Centralogic 
section) by pressing and holding down the corresponding Bank Select key, the channel name 
display at the top of the...

Centralogic section
 Reference Manual
14
INPUT DELAY field (input channels only)This field displays the delay status for the input channel. Press this field to open the INPUT 
DELAY 8ch window.1
DELAY ON/OFF indicator
Indicates the on/off status of the delay.
INSERT/DIRECT OUT fieldThis field displays the Insert/Direct out status. Press this field to open the INSERT/DIRECT 
OUT 8ch window.1
INSERT ON/OFF indicator
Indicates the insert on/off status.
2
DIRECT OUT ON/OFF indicator (input channels only)...

Centralogic section
 Reference Manual
15
If the destination bus is set to FIXED:
The SEND ON/OFF button for each bus is shown instead of the knob.TO STEREO/MONO fieldThis field displays the on/off status and pan/balance setting of the signal sent to the STEREO/
MONO bus.
This field varies depending on the type of the selected channel.
When an input channel or MIX channel is selected:1
TO STEREO PAN knob
Sets the pan position of a signal routed to the STEREO bus.
Press the knob to open the STEREO/MONO...

Input and output patching
 Reference Manual
16
Input and output patchingThis chapter explains how to edit the input patching and output patching, how to connect 
inserts, and how to use direct outputs.
When the CL series is in the initial state, the following input ports (jacks/ports) are patched to 
each input channel.
For CL5
For CL3
For CL1
When the CL is in the initial state, the output ports (jacks/ports) are patched to the following 
output channels.
CL console internal patching and Dante audio...

Input and output patching
 Reference Manual
17
Input patchingCL series consoles and I/O devices feature two types of patching: Dante audio network 
patching and CL console internal patching.
For Dante audio network patching, you will use the DANTE INPUT PATCH window. In this 
window, you can patch the CL console and I/O device inputs. Sixty-four (64) channels can be 
input from a Dante audio network to a CL series console. You can choose up to 64 channels 
from a maximum of 512 channels (logical value)...

Input and output patching
 Reference Manual
18
PATCH/NAME screen1
PATCH button
Indicates the currently-selected input port. If you press this button when selecting an 
icon or changing the channel name, you will return to the input port select screen.
2
Icon button
Indicates the icon that is selected for the corresponding channel. When you press this 
button, a screen will appear in which you can select an icon or sample name.
3
Channel name input box
Indicates the name that is assigned to the...

Input and output patching
 Reference Manual
19
PATCH/NAME screen1
PATCH button
Indicates the port that is patched to the output channel. If you press this button when 
another tab is active, a window will appear, enabling you to select the network and port.
2
Channel select button
Selects the channel to set.
NOTESwitching channels on this screen will not affect the channel selection on the console.
3
Channel icon button
Indicates the icon and color that are currently selected for the corresponding...

Input and output patching
 Reference Manual
20
CH SELECT screen1
Category select list
Select the category of the channel. The categories correspond to the following channels. 
They vary depending on the output port type.
•MIX/MATRIX.......................... MIX 1 - MIX 24, MATRIX 1 - MATRIX 8
•ST/MONO/MONI/CUE........... STEREO L, STEREO R, MONO (C), MONI L, MONI R, 
MONI C, CUE L, CUE R, SMON L, SMON R, SMON C, 
SMON LFE, SMON Ls, SMON Rs, MMTX L, MMTX R, 
MMTX C, MMTX LFE, MMTX Ls, MMTX Rs
•DIRECT OUT...