Yamaha Cl 5 User Guide

Input and output patching
 Reference Manual
21
• If you exceed the INSERT OUT or INSERT IN limitation, the   indicator will light up on the left.
• If the limit is exceeded, invalid ports will be marked with a strike-out line.
• If the limit is exceeded, the following ports will take priority per channel group (listed in the table 
above).
1
 INSERT 1 will take priority over INSERT 2.
2
 Lower-number channel will take priority.
INSERT/DIRECT OUT screen (1ch)INSERT fieldThis field enables you to make...

Input and output patching
 Reference Manual
22
INSERT IN HA fieldThis field will appear if you have selected an input port (that features a head amp) as the 
insert-in.6
+48V button
Switches head amp phantom power (+48V) (currently-selected for insert 1 and insert 2) 
on or off.
7
A.GAIN knob
Indicates the currently-selected head amp analog gain setting for insert 1 and insert 2. 
Press these knobs to control the parameter values using the multifunction knobs.
NOTE• If you have selected the OMNI IN jack...

Input and output patching
 Reference Manual
23
PORT SELECT screenDisplayed when you press either the INSERT OUT or INSERT IN button in the one-channel 
or the eight-channel INSERT/DIRECT OUT window. Set the input/output port used for 
insertion.1
Category select list
Selects the category of port. The categories correspond to the following ports. The 
displayed categories vary depending on the channel type.
•OMNI...................................... OMNI1 - OMNI8...

Input and output patching
 Reference Manual
24
INSERT/DIRECT OUT screen (1ch)1
DIRECT OUT fieldEnables you to make settings for direct output. Press one of four fields to choose PRE HPF 
(immediately before the HPF), PRE EQ (immediately before the EQ) or PRE FADER 
(immediately before the fader), or POST ON (immediately after the [ON] key) as the direct 
output position.
2
DIRECT OUT PATCH button
Displays the currently-selected Direct Out output port. Press this button to open the 
PORT SELECT window, in...

Input and output patching
 Reference Manual
25
PORT SELECT screenDisplayed when you press the DIRECT OUT PATCH button in the one-channel or the eight-
channel INSERT/DIRECT OUT window. Set the output port used for direct output.1
Category select list
Selects the category of output port. The categories correspond to the following output 
ports. The displayed categories vary depending on the channel type.
•OMNI/REC.............OMNI1-OMNI8, REC IN(L), REC IN(R)
•SLOT1....................SLOT1(1) -...

Input channels
 Reference Manual
26
Input channelsThis chapter explains various operations for input channels.Signal flow for input channelsThe input channels comprise the section that  processes signals received from the I/O 
devices, rear panel input jacks, or slots 1-3,  and sends them to the STEREO bus, MONO bus, 
MIX buses, or MATRIX buses. There are two types of input channels, as follows.MONO channelsThese channels are used to process monaural signals. When the CL series console is in the 
default...

Input channels
 Reference Manual
27
•Pan Adjusts the panning of signals sent from the input channel to the STEREO bus. For the 
STEREO channel, you can switch between  PAN and BALANCE. The BALANCE parameter 
adjusts the volume balance of the left/right signals sent from the STEREO channel to the 
STEREO bus. You can turn on PAN LINK in the BUS SETUP window so that the setting of 
the PAN parameter will also be applied to signals sent to two MIX or MATRIX buses that 
are set to stereo.
• LCR...

Input channels
 Reference Manual
28
PATCH/NAME screen When selecting the PATCH tab
1
PATCH button
Indicates the currently-patched port. If you press this button when another tab is active, 
a window will appear, enabling you to select the network and port.
2
Icon button
Indicates the icon and color that are currently selected for the corresponding channel. 
When you press this button, a screen will appear in which you can select an icon or 
sample name.
3
Channel name input box
Indicates the...

Input channels
 Reference Manual
29
 When selecting the NAME tabYou can directly enter a channel name on the keyboard screen.HA (head amp) settingsYou can make HA (Head Amp) related settings (phantom power on/off, gain, phase) for the 
input channel.
• To adjust only the HA analog gain, use the GAIN knob in the SELECTED CHANNEL 
section.Setting the gainHead amp settings are made in the GAIN/PATCH window. NOTE
• The PAD will be switched on or off internally when the HA gain is adjusted between +17 dB and...

Input channels
 Reference Manual
30
NOTE• If a slot is patched to the channel, the type of the  slot/MY card and the slot meter will be displayed.
• If a rack is patched, the type of rack and type of effect will be displayed.• +48V button Switches head amp phantom power (+48V) on or off.
• A.GAIN (analog gain) knob Indicates the analog gain of the head amp. Adjust the gain by using the 
multifunction knobs. If the Gain Compensation function is turned on, an 
indicator appears, showing the analog  gain...