Yamaha Av1 Service Manual

En121
■ Zone RenameChanges the zone names displayed on the front display or TV screen.
■  Setup procedure1
Use the cursor keys to select a zone to be renamed and press ENTER.
2
Press ENTER, use the cursor keys to rename, and then press ENTER again.
3
Use the cursor keys to select “OK” and press ENTER. To clear the entry, select “CLEAR”.
4
To exit from the menu, press ON SCREEN.
FunctionConfigures the functions that make this unit easier to use.
■  Auto Power DownSets the amount of time for auto-standby....

En122
■ Display SetConfigures the settings related to the front display and TV screen display.❑  Front Panel DisplayConfigures the front display settings.
Dimmer
Adjusts the brightness of the front display.
Setting range
-4 ~ 0 (higher to brighten)
Default
0
Scroll
Sets the scrolling manner of the front display.
The display scrolls automatically  if the text exceeds 14 characters.
Settings
❑ Short MessageSelects whether to display short messages  on the TV screen when this unit is operated 
(input...

En123
❑ 
Target Source
Specifies the output level of the electronic signal transmitted with each input switching 
when “Trigger Mode” is set to “Source”.
Choices
AV1~7, V-AUX, AUDIO1~4, PHONO, TUNER,  (network sources), USB, DOCK, MULTI CH
Settings
❑  ManualSwitches the output level for electronic signal transmission m anually when “Trigger 
Mode” is set to “Manual”. This setting can also be used to confirm proper function of 
the external component connected via the TRIGGER OUT jack.
Choices
■  Memory...

En124
You can view information about this unit using the TV screen.1
Press ON SCREEN.
2
Use the cursor keys to select “Information” and press ENTER.
3
Use the cursor keys ( / ) to select an information type.
4
To exit from the menu, press ON SCREEN.
Typ es  of  i n for m ati on■ Audio SignalDisplays information about the current audio signal. Even when this unit is set to output bitstream signals directly, the signal may be converted depending on 
the specifications and settings of the playback device.■...

En125
■ NetworkDisplays the network information on this unit.■ SystemDisplays the system information on this unit. If this unit detects a newer firmware over the network, “!” (exclamation mark) appears at the upper right of 
the “Information” and “System” icons, and the corresponding message will be displayed in this screen. You 
can update the firmware of this unit by pressing ENTER in this screen and following the procedure in 
“Updating the firmware of this unit” (p.137).■  ZoneDisplays information...

En126
ADVANCED SETUP menu itemsChanging the speaker impedance setting (SPEAKER IMP.)Change the speaker impedance settings of unit depending on the impedance of the 
speakers connected.
Settings
Turning on/off the remote control sensor (REMOTE SENSOR)Turn on/off the remote control sensor on the main unit. While the remote control sensor 
is turned off, you cannot control this unit from the remote control.
Settings
Selecting the remote cont rol ID (REMOTE CON AMP)Select the remote control ID of the main...

En127
5
Press ENTER to confirm the setting.
Once the remote control ID is registered successfully, “OK” appears in the display window.
If “ERROR” appears, registration failed. Repeat from step 3.
6
To exit from the setup menu, press SETUP.
 The registered remote control codes (p.129) are not cleared even if you change the remote control ID.Changing the frequency step setting (TUNER FRQ STEP)(Asia and General models only)
Change the frequency step setting of this unit depending on your listening...

En128
Backing up/recovering the settings (RECOV./BACKUP)Creates backup of the settings of this unit, or recovers the settings from the backup.■ Backup/recovery procedure1
Press STRAIGHT repeatedly to select “BACKUP” or “RECOVERY” and press INFO to 
start the process.Choices
Restoring the default settings (INITIALIZE)Restores the default settings for the selected item.
Choices
Updating the firmware (FIRM UPDATE)New firmware will be released irregularly  for the purpose of additional features or 
product...

En129
2
3
5
1
46
TUN./ CH
ENHANCER
SUR.
DECODE
HDMI OUT
MEMORY
INFO AM
PA R T YFM
0
  10
LEVEL
ENT
SETUP
ZONE
8
7
SLEEP
9
SOURCE
RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTIONTUN./ CH
SOURCERECEIVER
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]...

En130
5
Use the numeric keys or cursor keys to enter the 
4-digit remote control and press ENTER.Once the remote control code is set successfully, “OK” 
appears in the display window.
If “ERROR” appears, registration failed. Repeat from 
step 3.
6
To exit from the setup menu, press SETUP.
❑ TV operationsOnce you have set the remote control code for your TV, you can 
control it using the TV operation keys regardless of an input source 
selected on this unit.■ Setting the remote control codes for 
playback...