Yamaha Av1 Service Manual

En111
❑ 
Subwoofer 1, Subwoofer 2
Selects whether or not subwoofer is connected to the SUBWOOFER 1 or 
SUBWOOFER 2 jack and its phase.
Settings
 When the bass sound is lacking or unclear, switch the subwoofer phase.❑ SWFR LayoutSelects a subwoofer layout when 2 subwoofers are used.
Settings
 This setting is not available when “Subwoofer 1” or “Subwoofer 2” is set to “None”.❑ Extra BassSets the speakers to produce the front channel low-frequency components.
Settings
 This setting is not available when...

En112
■ Parametric EQAdjusts sound quality of tone with an equalizer.❑  PEQ SelectSelects a type of equalizer to be used.
Settings
 “YPAO:Flat”, “YPAO:Front” and “YPAO:Natural” are available only when the measurement results of “Auto 
Setup” have already been saved (p.47).❑  PEQ Data CopyCopies the parametric equalizer values acq uired with “Auto Setup” (p.47) to the 
“Manual” fields for fine adjustment.
Choices
■  Manual equalizer adjustment1
Set “PEQ Select” to “Manual” and press ENTER.
2
Use the...

En113
SoundConfigures the audio output settings.■ LipsyncAdjusts the delay between video and audio output.❑  AutoAdjusts the delay between video and audio output automatically when a TV that 
supports an automatic lipsync function is con nected to this unit via HDMI. If necessary, 
you can fine-adjust the audio output ti ming. “Offset” shows the difference between 
automatic adjustment and fine adjustment.
Setting range
0ms ~ 500ms (1ms steps)
Default
0ms
❑  ManualAdjusts the delay between video and...

En114
■ Adaptive DSP LevelSelects whether to automatically adjust the CINEMA DSP effect level in conjunction with 
volume adjustments.
Settings
VideoConfigures the video output settings.■  Analog to Analog ConversionEnables/disables the video conversion (p.149) between the analog video jacks 
(COMPONENT VIDEO, S VIDEO and VIDEO).
Settings
 This function works only when “Monitor Out Assign” (p.120) is set to “Main”.
 This unit does not convert 480-line and 576-line video signals interchangeably....

En115
■ ProcessingEnables/disables the video signal processi ng (resolution, aspect ratio and video 
adjustments).
Settings
❑  ResolutionSelects a resolution to output HDMI video si gnals when “Processing” is set to “On”.
Settings
 If you need to select a resolution that is not supported by your TV, set “MONITOR CHECK” (p.127) in the 
“ADVANCED SETUP” menu to “SKIP” and try again. (Note that output videos may not be displayed on your 
TV normally.)❑  AspectSelects an aspect ratio to output HDMI vid eo...

En116
Edge Enhancement
Adjusts the enhancement effect of video edges manually when “Resolution 
Enhancement” is set to “Manual”.
Setting range
0 ~ 50
Default
0
Noise Reduction (NR)
Selects whether to use the noise reduction functions.
Settings
Mosquito NR
Selects the effect of the mosquito noise reduction when “Noise Reduction (NR)” is set to 
“Manual”. Mosquito noise is a distortion that comes out at the video edges.
Settings
Block NR
Selects the effect of the block noise reduct ion when “Noise...

En117
HDMIConfigures the settings related to HDMI.■ HDMI ControlEnables/disables HDMI Control (p.150).
Settings
 To use HDMI control, you need to perform the HDMI Control link setup (p.150) after connecting HDMI 
Control-compatible devices.❑  TV Audio InputSelects an audio input jack of this unit  to be used for TV audio input when “HDMI 
Control” is set to “On”. The input source of this unit automatically switches to TV audio 
(input jack selected in here) when the TV input is switched to its built-in...

En118
■ Audio OutputSelects a device to output audio. The “Amp” and “HDMI OUT1” settings are available only when “HDMI Control” is set to “Off ”.❑  AmpEnables/disables the audio output from the speakers connected to this unit.
Settings
❑ HDMI OUT1, HDMI OUT2Enables/disables the audio output from a TV connected to the HDMI OUT 1 jack or 
HDMI OUT 2 jack.
Settings
■ Standby ThroughSelect whether to output videos/audio (input through HDMI jacks) to the TV when this 
unit is in standby mode.
Settings
 This...

En119
■ Network StandbySelects whether to turn on this unit by the command from other network devices 
(network standby).
Settings
■ MAC Address FilterSets the MAC address filter to limit acces s to this unit from other network devices.❑ ModeEnables/disables the MAC address filter.
Settings
❑ Address SetupSpecifies the MAC addresses (up to 10) of t he network devices that will be permitted 
access to this unit when “Mode” is set to “On”.
Multi ZoneConfigures the multi zone settings.■  Zone2 Set, Zone3...

En120
❑ 
Mono
Switches between stereo and monaural for Zone2 or Zone3 output.
Settings
■ Digital Out AssignSelect the zone (main zone or Zone4) for whic h the AV OUT/ZONE4 (digital optical) jack 
is used.
Settings
Main (default), Zone4
■  Monitor Out AssignSelect the zone for which the MONITOR  OUT/ZONE OUT (COMPONENT VIDEO, S 
VIDEO and VIDEO) jacks are used.
Settings
Main (default), Zone2, Zone3, Zone4
 The video conversion between the analog video jacks does not work for multi-zone video output. To...