Xerox Phaser 6180MFP User Manual

User Safety
Phaser® 6180MFP Multifunction Printer 
1-2
User Safety
Your printer and the recommended supplies have been designed and tested to meet strict safety 
requirements. Attention to the following information ensures the continued safe operation of 
your printer.
Electrical Safety
■Use the power cord supplied with your printer.
■Plug the power cord directly into a properly grounded electrical outlet. Make sure each 
end of the cord is securely connected. If you do not know if an outlet is grounded,...

User Safety
Phaser® 6180MFP Multifunction Printer 
1-3
 
If you notice unusual noises or odors:
1.Turn off the printer immediately.
2.Disconnect the power cord from the electrical outlet. 
3.Call an authorized service representative to correct the problem.
The power cord is attached to the printer as a plug-in device at the back of the printer. If it is 
necessary to disconnect all electrical power from the printer, disconnect the power cord from 
the electrical outlet.
 
Warning: Do not remove the...

User Safety
Phaser® 6180MFP Multifunction Printer 
1-4
Maintenance Safety
■Do not attempt any maintenance procedure that is not specifically described in the 
documentation supplied with your printer.
■Do not use aerosol cleaners. The use of supplies that are not approved may cause poor 
performance and could create a hazardous condition.
■Do not attempt to open, reuse, or burn any consumables or routine maintenance items. For 
information on Xerox supplies recycling programs, go to www.xerox.com/gwa
....

User Safety
Phaser® 6180MFP Multifunction Printer 
1-5
Operational Guidelines
■Do not block or cover the slots and openings on the printer. The printer may overheat 
without adequate ventilation.
■For optimum performance, use the printer at elevations below 3,100 m (10,171 ft.).
■Do not place the printer near a heat source.
■Do not place the printer in direct sunlight to avoid exposing light-sensitive components 
when the doors are open.
■Do not place the printer in line with the cold air flow from an...

User Safety
Phaser® 6180MFP Multifunction Printer 
1-6
Moving the Printer
Follow these guidelines to avoid injuring yourself or damaging the printer:
■Turn off the printer and unplug all power cables before moving the printer.
■Set the scan bar lock switch to the locked position.
6180mfp-001
6180mfp-064
Downloaded From ManualsPrinter.com Manuals 

User Safety
Phaser® 6180MFP Multifunction Printer 
1-7
■Always use three people to lift the printer.
■Always lift the printer from the designated lift points.
■Carry the printer without tilting it.
Caution: Do not tilt the printer more than 10 degrees to the front/back or right/left. 
Tilting more than 10 degrees may lead to consumables inside the printer spilling out.
Note: The rear side of this printer is heavier than the front. Be aware of this weight 
difference when moving the printer.
■Do not place...

User Safety
Phaser® 6180MFP Multifunction Printer 
1-8
Safety Symbols Marked on Printer
Use caution (or draws attention to a particular 
component). See the manual(s) for information. 
Hot surface on or in the printer. Use caution to 
avoid personal injury.
It may take 30 minutes for the fuser to cool down.
Do not touch the item.
Do not burn the item.
Do not expose the item to sunlight.
Do not expose the item to light.
Recycle the item.
Downloaded From ManualsPrinter.com Manuals 

Printer Specifications
Phaser® 6180MFP Multifunction Printer 
1-9
Printer Specifications
Physical Specifications
■Width: 460 mm (18.1 in.)
■Depth: 520 mm (20.5 in.)
■Height (with scanner lid up): 1080 mm (42.5 in.)
■Weight: 
■6180MFP-N: 40 kg (88.2 lb.) including consumables
■6180MFP-D: 41 kg (90.4 lb.) including consumables
Environmental Specifications
50° F to 95° F (10° C to 32° C) and a relative humidity range of 15 percent to 80 percent
Electrical Specifications
Electrical Specifications
■110-127...

Printer Specifications
Phaser® 6180MFP Multifunction Printer 
1-10
Warm-Up Time
■30 seconds or less (when power is switched on, temperature: 22° C)
The printer’s electrical system is ready 10 seconds after switching on the printer.
Performance Specifications
Resolution
Maximum Resolution: 600 × 600 dpi
Print Speed (Letter/ A4)
Copy Speed
■Color: 20 cpm
■Black & White: 31 cpm
Print Mode1-Sided Printing (ppm) 2-Sided Printing (ipm)
Color Black & White Color Black & White
600 dpi standard 20 / 20 31 / 30 14...

Printer Specifications
Phaser® 6180MFP Multifunction Printer 
1-11
Controller Specifications
Processor Speed
400 MHz processor
Memory
■Printer: 256 MB
■Copy/Scan/Fax: 128 MB
Expandable to combined memory of 1408 MB
Resident Fonts
■PCL 5/PCL 6
■PostScript 3
Interfaces
■Ethernet 10/100 Base Tx
■Universal Serial Bus (USB 2.0)
■Parallel
Downloaded From ManualsPrinter.com Manuals