Xerox Phaser 3155 User Manual
Have a look at the manual Xerox Phaser 3155 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Phaser 3140/3155/3160 Printer Service Manual8-11 Service Parts Disassembly Fuser PL9.0 Wa rn i n g Allow the Fuser to cool 30 minutes before performing this procedure. 1. Remove the Rear Cover (page 8-26). 2. On the Power Supply, remove CON1. Note Press the connector lock to remove CON1. P/JCON1s3160-038 s3160-068 Downloaded From ManualsPrinter.com Manuals
8-12Phaser 3140/3155/3160 Printer Service Manual Service Parts Disassembly 3. Remove the Fuser Thermistor cable from the Controller Board. The connector number varies depending on your printer model. See the following illustration. 4. Remove 4 screws (10 mm, silver, tap) securing the Fuser. 5. Pull the Fuser out of the printer. 3160: CN8 3155: CN12 3140: CN12 s3160-048 s3160-049 Downloaded From ManualsPrinter.com Manuals
Phaser 3140/3155/3160 Printer Service Manual8-13 Service Parts Disassembly Thermistor PL9.0.11 Wa rn i n g Turn the printer power Off and allow the Fuser to cool 30 minutes before performing this procedure. 1. Remove the Fuser (page 8-11). 2. Remove 1 screw (10 mm, silver, tap) securing the Thermistor. 3. Remove the wiring harness from the harness guide and remove the Thermistor. s3160-056 Downloaded From ManualsPrinter.com Manuals
8-14Phaser 3140/3155/3160 Printer Service Manual Service Parts Disassembly Thermostat PL9.0.12 Wa rn i n g Turn the printer power Off and allow the Fuser to cool 30 minutes before performing this procedure. 1. Remove the Fuser (page 8-11). 2. Remove 3 screws (8 mm, black) that secure the Thermostat. 3. Lift the Thermostat away from the Fuser Cover. 4. Disconnect the wiring harness connect ors CN49 & CN50 from the Thermostat. 5. Remove the Thermostat. s3160-064 CN49 CN50 Downloaded From ManualsPrinter.com Manuals
Phaser 3140/3155/3160 Printer Service Manual8-15 Service Parts Disassembly Fuser Lamp PL9.0.13 Wa rn i n g Turn the printer power Off and allow the Fuser to cool 30 minutes before performing this procedure. 1. Remove the Fuser (page 8-11). 2. Release the 2 tabs on the right Fuser lamp cap and remove the cap. Caution Take care to not over flex the tabs as they can easily break. s3160-105 Downloaded From ManualsPrinter.com Manuals
8-16Phaser 3140/3155/3160 Printer Service Manual Service Parts Disassembly 3. Release the 3 tabs on the left Fuser lamp cap and remove the cap. 4. Disconnect the lamp wires on both sides of the Fuser. s3160-106 s3160-055 Downloaded From ManualsPrinter.com Manuals
Phaser 3140/3155/3160 Printer Service Manual8-17 Service Parts Disassembly 5. Remove 2 screws (8 mm, black, tap), one on each end of the Fuser, and gently slide the Fuser Lamp out of the Fuser. Caution Hold the halogen lamp by the ends so there is no transfer of oil from your hands onto the lamp, which can damage the lamp. Heat Roller PL9.0.36 Wa rn i n g Turn the printer power Off and allow the Fuser to cool 30 minutes before performing this procedure. 1. Remove the Fuser (page 8-11). 2. Remove the Fuser Lamp (page 8-15). s3160-136 Downloaded From ManualsPrinter.com Manuals
8-18Phaser 3140/3155/3160 Printer Service Manual Service Parts Disassembly 3. Remove 2 screws (6 mm, silver). 4. Remove 2 screws (6 mm, silver). 5. Lift the Fuser Cover off the Fuser. s3160-053 s3160-054 Downloaded From ManualsPrinter.com Manuals
Phaser 3140/3155/3160 Printer Service Manual8-19 Service Parts Disassembly 6. Open both Fuser lever arms, and then slide the Heat Roller out of the Fuser frame. 7. Remove the Fuser Gear from the Heat Roller. Replacement Note When reassembling the Fuser, gently pull the claw guides towards the front of the Fuser to avoid breaking them. Starting on the right, pull the right-most claw forward and then lower the cover slightly to hold the claw in place. Move to the left and repeat the process with the next claw. Repeat until each claw is pulled forward and secure the cover. s3160-058 s3160-133 Downloaded From ManualsPrinter.com Manuals
8-20Phaser 3140/3155/3160 Printer Service Manual Service Parts Disassembly Pressure Roller PL9.0.34 Wa rn i n g Turn the printer power Off and allow the Fuser to cool 30 minutes before performing this procedure. 1. Remove the Fuser (page 8-11). 2. Remove the Heat Roller (page 8-17). 3. Rotate the Right Bushing counter-clockwise and then remove it. s3160-059 Downloaded From ManualsPrinter.com Manuals