Vodavi Triad 1/2/3 System Programming Manual

3-14 Page  A I ntro ductio n
Des crip ti on
Each CO Line may be ass ig ned to ring a ny s ta tion in the sys te m; UCD,  
Voice Mail or  Hunt Group,  or  Off-Net  (via speed dial).  CO Line  ringing is 
pr ogra mmed  on a pe r C O L ine  des ti nat i on bas is.  Each d est i nat ion m ay be  
des ig nat ed  to  ri ng du ri ng t he  day , dur i ng t he  nigh t,  or  re cei ve  bot h D ay 
and  Nig ht ringin g. S ta tions that a re  as sig ned  for  initial ring -in mu s t ha v e 
a L OO P but ton (s) t o...

Page A  Introduction 3-15
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The Co  Line Identification  Display feature allows  the entry  of a  name for 
each line (trunk) connected to the system.  Once entered into the 
dat aba se , LC D p hones , i nclu ding  t he A t te nda nt  st at ions , r ece iv e t he  
pr ogra mmed  l ine  nam e i n p la ce of  t he d efa ult  LI NE  XX X me ss age . T his  
app li es  t o al l  li ne  call  p roce ssi ng...

3-16 Page  A I ntro ductio n
CO  Di rec ti on
Pro g ram mi ng  S te ps
1 . Pr es s t he  TR UN K DI R EC TI ON  fl exi bl e b utt on. (FLASH  40, Page A, 
Bu tton  #12).  Th e f oll owing  me ssa ge  dis pl ays:
2. Enter a valid number (0-3) on  the dial pad which corresponds to the 
desired CO type:
[0] =  Out-of -S ervice ( OOS)
[1] =  In com ing  Onl y
[2] =  Outgoi ng Onl y
[3] =  Both Incoming  and  Outgoi ng
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates....

Page A  Introduction 3-17
Display Ring Assignments
Pro g ram mi ng  S te ps
1. Press FL ASH  40, Pag e  A, Bu tton  #13 to d isp lay  ring  ass ign ments. 
Assignments are displayed in sets of 8, up to the number 
programmed. The following  format displays the  assignments.
DDD = Destination
RR :
     [0 ] = N o R i n g
1  [ D ] = D ay  R in g
2  [ N ] = N igh t  Rin g
3  [ D N]  = Da y / N ig ht  Ri ng
4   [ S]  =  S pecial  Only
5   [ DS]  =  Da y/Sp ecia l
6  [ N S] = N ight/Sp ecia l
7   [A] = All...

3-18 Page  A I ntro ductio n
Des crip ti on
The  DI D/T IE  Si gna li ng fe at ur e ca n be  pr ogr amme d f or o ne-w ay d ir ect  
access inward  dialing access to specific  stations on specific DID  lines 
without going  through an Attendant answering position.
91 1 Tru n k
Pro g ram mi ng  S te ps
1. Press FL ASH  40, Pag e  A, Bu tton  #15 to designate the line  for  911 
use . Th e f oll owin g me ssa ge  dis pl ays:
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le...

Page A  Introduction 3-19
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
4. Reset the  KSU
-or -
Reset only the  card using “config” without resetting  the whole 
te le phone  s wit c h. To d o t his , t ype  config at  t he Enter  Passwor d 
pr ompt . T hen  ty pe r< sp ac e>k (k = sl ot numbe r).  For  ex ampl e, 
r< sp ac e>2 i ndi c ate s  tha t  the  B R I...

3-20 Page  B I ntro ductio n
Page B Introduction
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode. If Page 
B CO  Li ne  fe at ure s m ust  be  chang ed:
1. Press FLASH and  di al  [40 ].  The following message displays:
2. Enter a valid number for the range of lines being programmed. If only 
on e l in e i s  bei ng  prog ram med,  ent er  t hat  num ber  t wi ce  (0 0 1  00 1) .
3. Press...

Page B Introduction 3-21
Range  pro gra mmin g le ts  the  pr ogra mmer  chang e a s peci fi c p ar ame te r or  
a few  parameters for an entire range of  CO Lines leaving  intact the 
re mai ni ng da ta  fi el ds  tha t  do not r eq uir e  ch ange . T hose  data  fi el ds 
continue to operate with the previously programmed data.
Whe n pr ogr ammi ng t he  P age  B f eat ur es , t he  fl exi ble  b utt ons  ar e 
mapp ed as fol lows :
T-1 Signaling Type
Pro g ram mi ng  S te ps
1. Pres s the  T- 1...

3-22 Page  B I ntro ductio n
2. Enter a  valid number (0-7) on  the dial pad that corresponds to one of 
the following  types:
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Des crip ti on
The T-1 trunk  card provides the Tr iad Digital Systems with the  ability to 
connect to digital  T-1 trunk circuits. The T-1  trunk  card supports  either 
the standard D4  framing format with Alternate Mark Inversion  (AMI) or 
Ext end ed  Supe rf ra me ( ESF -B8 ZS)  forma t...

Page B Introduction 3-23
T-1  trunking provides services  called Automatic Number  Identification 
(ANI) and Dialed Number Identification Service (DNIS). The T-1 feature 
supports both of these services. The Tr iad Di gi ta l S yst e ms s uppor t  A NI,  
DNI S,  or  an  AN I  and D NI S comb ina ti on on  a p er  chan nel  (l ine ) b asi s.  By 
def au l t,  th e T -1  S igna l  Type  O pt io n  is  Lo o p  St ar t.
T- 1  R i n g b ac k
Pro g ram mi ng  S te ps
1 . Pr es s t he  R I NGBAC K fl exi bl e...