Vodavi Triad 1/2/3 System Programming Manual

3-64 IS DN Pro gram ming - Pag e A
Me ss ag e  Exc ha n g e Tim er
Pro g ram mi ng  S te ps
1. Press the MSG  EXCH ANG E TIMER flexible b utton ( FLA SH 45,  Pag e B, 
Bu tton  #8).
2 . Ent er  a  val id  nu mbe r  (0 0- 99  s ec o nds ) o n  the  di al  pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Minimum XID Retransmission
Pro g ram mi ng  S te ps
1. Press the MIN XID  RETRANSMSN  flexible button (FLASH 45, Pag e  B, 
Bu tton  #9).
2 . Ent er  a  val id...

IS DN Programm in g - Page  A 3 -65
Set- Up Timer
Pro g ram mi ng  S te ps
1. Press the SET  UP TIMER flexible button (FLASH 45, Pag e  B, 
Bu tton #11).
2 . Ent er  a  val id  nu mbe r  (0 0- 99  s ec o nds ) o n  the  di al  pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Disconnect Timer
Pro g ram mi ng  S te ps
1. Press the DISCONNECT TIMER  flexible button ( FLASH 45, Pag e  B, 
Bu tton  #12).
2 . Ent er  a  val id  nu mbe r  (0 0- 99  s ec o nds ) o n  the...

3-66 IS DN Pro gram ming - Pag e A
Li nk  D is c o nn ec t
Pro g ram mi ng  S te ps
1 . Pr es s t he  LI NK D IS CON NEC T f le xib le  but ton  (FLASH 45, Page B, 
Bu tton  #14).
2 . Ent er  a  val id  nu mbe r  (2 0- 30  s ec o nds ) o n  the  di al  pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
Call Pro ce eding
Pro g ram mi ng  S te ps
1 . Pr es s t he  CA LL  P R OC EED IN G fl exi bl e  but ton (F LA SH 45 ,  Pa ge  B , 
Bu tton  #15).
2 . Ent er  a  val...

T-1 A la rm Programming 3 -67
Restart Request Timer
Pro g ram mi ng  S te ps
1. Pres s the RESTART  REQ TIMER  flexib le button ( FLASH 45, Pag e  B, 
Bu tton  #17).
2. Enter a  valid  numbe r (0-200 s econds ) on  the  dial pa d.
3. Press the HOLD  button. A confirmation tone is heard and the  display 
up dates.
T-1 Alarm Programming
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode.
1. Press...

3-68 T-1 Al arm  Prog ra mming
Des crip ti on
The  T -1  Tr unk  c ard  and  t he s yst em  sof twa re  pr ovi de  tool s  to  hel p d et ec t  
and  isolate problems which may occur with  the T-1 circuit. There are six 
LED s m ounted on  th e outside edge  of the T- 1  Trunk ca rd  which  eith er 
light or flash to indicate a  variety of  conditions on the T-1 circuit. The 
Ce ntral Of fice  Main te nance  Cente r can s end  a command  to place  the  CS U 
int o Li ne  Loop Ba ck mode . I f t he re  is...

T-1 A la rm Programming 3 -69
[0] =  Disab le d
[1] =  Ena ble d
3. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay u pdat es .
Des crip ti on
A Receive Carrier Loss (RCL) condition is declared when no bits have been 
received by the T-1 Trunk  card for 150ms. It causes an Out of Frame (OOF) 
condition,  and 2.5 seconds later a  RED  Carrier Failure  Alarm (CFA) state. 
Dur ing  th e t i me  the  RCL  and  RED  al ar m ar e  de cl ar ed , i ncomi ng an d 
outg...

3-70 T-1 Al arm  Prog ra mming
Des crip ti on
The  Bl ue A l arm  si gnal  i s an  unfr ame d al l  ones  si gnal . I t  is  tr ans mi tt ed  by a  
remote  device  (usually a CSU) and when received, indicates a 
tr ans mis si on fa il ure  up st re am o f t hat  de vi ce t owar d  the  l ocal  end . T he 
AI S  al ar m si gna l i s  al so kn own as  t he keep alive s ign al in th at it  p re ven ts  
the T-1 circuit  repeaters from  malfunctioning when transmit from the 
remote end  is lost. By default,...

T-1 A la rm Programming 3 -71
Red Alarm
Pro g ram mi ng  S te ps
1. Press the RED ALARM  flexible button ( FLASH 47, Butto n #4 ). 
Button # 4 and  Button # 11  LEDs  are  lit stea dy.  The fo llowing  mes sag e 
di spl ays:
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD button to save entry.  A  confirmation tone  is heard and 
t he  di spl ay  updat es .
4. Continue  pr ogr ammi ng the  Re d Ala rm  par ame te rs  us ing  the  s te ps...

3-72 T-1 Al arm  Prog ra mming
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
4. Continue to program Bipolar Variations  Alarm parameters  using the 
s te ps  in  thi s  se cti on f or C le ar ing  t he  ala rm,  Mi nor  al ar m, Maj or  al ar m, 
Time Period, and Attendant display.
Des crip ti on
Exce ssi ve  Bi pola r  Viol at ion s (BPV)  ar e d ecl ar ed...

T-1 A la rm Programming 3 -73
Data Errors Alarm
Pro g ram mi ng  S te ps
1 . Pr es s t he  DATA  ER R O RS  fl ex ibl e  but ton (FLASH  47, Button  #7). 
Button # 7 and  Button # 11  LEDs  are  lit stea dy.  The fo llowing  mes sag e 
di spl ays:
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD button to save entry.  A  confirmation tone  is heard and 
t he  di spl ay  updat es .
4. Continue to program the Data  Error Alarm parameters...