Vodavi Triad 1/2/3 System Programming Manual

3- 4 Page  A I ntr o ducti o n
DTMF / Dial Pulse Programming
1 . Pr es s t he  DT M F/ DI AL  P ULSE  fl ex ibl e  but ton (FLASH  40, Page A, 
Bu tton  #1).
2. Enter a 0 or 1 that corresponds with the following entries:
[0] =  Dial Puls e
[1] =  DT MF
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Des crip ti on
Each  ind iv idua l  outs ide line can  be programmed to b e D TMF  (ton e) o r 
dial  pulse. By  default,  all lines  are set for DTMF.
DTMF /
DPCO / 
PB XUNADISA 
CO  T O CO...

Page A  Introduction 3-5
CO /  PBX Programming
Pro g ram mi ng  S te ps
1 . Pr es s t he  CO /P BX  fl exi bl e b utt on ( FLA SH 40,  Pag e A, Butto n #2).
2 . Ent er  a  0 or 1 whic h c orr es ponds  wi th the  fo ll owing ent r ie s:
[0] =  PBX 
[1] =  CO 
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Des crip ti on
Each ind iv idua l outs ide line connected to the sy stem may be 
programmed as a  CO or PBX line.  Use the PBX mark when identifying 
Ce ntrex  line s.  By de fault,...

3- 6 Page  A I ntr o ducti o n
DIS A CO- to- CO
Pro g ram mi ng  S te ps
1. Press the DISA CO-TO-CO  flexible button ( FLASH 40, Pag e  A, 
Bu tton #4).
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Des crip ti on
The DISA  CO-to-CO (or Conference)  mark on  the CO line governs  a DISA 
caller’s  ab ility  to  acces s other ou tside  line s.  CO line s m ust hav e  DIS A CO-
to- CO  e...

Page A  Introduction 3-7
Pr iva cy
Pro g ram mi ng  S te ps
1 . Pr es s t he  P R IVAC Y  fl exi bl e b utt on ( FLA SH 40,  Pag e A, Butto n #5). 
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] =  Disab le d
[1] =  Ena ble d
3. Press HOLD to save the entry. A confirmation  tone is  heard.
Disabling Privacy F unction
The  sy st em  c an b e p rogr amm ed  to  el imi nat e  CO  Li ne  P ri vac y , whi c h 
allows  anothe r  station  to  join e xis ting o uts ide  line  conv...

3- 8 Page  A I ntr o ducti o n
Loop Supervision Programming
Pro g ram mi ng  S te ps
1 . Pr es s t he  LOO P  SUP V  fl exi ble  b utt on ( FLASH 40, Pag e  A, Button  #6).
2. Enter a valid number (1-9) on  the dial pad which corresponds to 
100-900 ms. (0 = disabled).
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
Loop  Supe rv is ion  is  use d p ri mar il y w it h DI S A,  Voi ce  M ai l /A ut o A tt e ndant  
and wit h un supe rv ise d con...

Page A  Introduction 3-9
DISA Programming
Pro g ram mi ng  S te ps
1. Press the DISA flexible button (FLASH 40, Page  A, Bu tton  #7).
2 . Ent er  a  val id  numbe r  (0 -5 ) on  the  di al  pa d t o i ndi ca te  t ype  of  DI SA 
desired.
[0] =  No D IS A
[1] =  24-H our  DISA
[2] =  Ni ght  DISA
[3] =  24-H our  DISA with  forwarding
[4] =  Night  DISA with  forwarding
[5] =  Telecen te r  24-Hour D IS A  with f orward ing
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the...

3-10 Page  A I ntro ductio n
CO  Li ne  Gr ou p  Pr ogram m in g
Pro g ram mi ng  S te ps
1 . Pr es s t h e  CO  L I N E  G R OU P  f le x i b le  b u tt o n  ( FLASH 40, P ag e A, 
Bu tton #8).
2. Enter a valid number on the dial pad (0-23)  which corresponds to 
Groups 0-23.
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
Twenty four line groups are  available  for CO line assignment. Groups 
shoul d b e a ssi gne d a ccor di ng t o t ype  (l...

Page A  Introduction 3-11
Clas s o f S ervice  (CO S)
Pro g ram mi ng  S te ps
1 . Pr es s t he  LI NE  COS  fl ex ibl e  but ton (FLASH 40, Page A, Bu tton #9).
2. Enter a valid number on the dial pad (1-5) which corresponds to five 
p ossi bl e  clas s-o f-se r vi ce t o whi ch a  l ine  may  be  as si gned :
COS1 = No restric tions
COS 2  =  Ta bl e A  g ov er ns,  St at ion  COS  2  and  4  ar e m onit ore d
COS 3  =  Ta bl e B  gover ns,  St at ion  COS  3  an d 4  ar e  moni tor ed
COS 4  = Re stri...

3-12 Page  A I ntro ductio n
CO Line Ringing Assignments
Pro g ram mi ng  S te ps
1 . Pr es s t he  RI NG ASS IGN MENT  fl exi bl e  butt on (F LA SH 40 ,  Pa ge  A,  
Bu tton  #10).  Th e d isp lay  shows  t he  foll owi ng i nfor mat ion :
2. Enter a  valid  De stina tion (D DD)  and  Rin g type  (R) f ollowed  by the  
H OLD  but ton . A confi r mat ion  tone  i s  hear d a nd t he  di spl ay  updat es .
Tab l e 3- 3:  C la ss o f  Ser v ic e (C OS)
S
T
A
T
I
O
N
C
O
SCO LI NE CLA SS O F SE RVI CE...

Page A  Introduction 3-13
Adding Multiple Stations
Ent er : DDD R HO LD D DDR HOLD  DD DR HO LD ...e tc.
(Example:  1073  HOLD, 1083 HOLD, 1093 HOLD)
Deleting a Single Station
Ent er : DDD 0 HOLD
(Example: 1080 HOLD)
Deleting Multiple  Stations
Ent er : DDD 0 HOLD  DD D0  HO LD.. .e tc.
(Example: 1080 HOLD, 1090 HOLD)
Table 3-4: CO Line Ringing As signments
Valid 3- Digit Destina tions (DDD) V alid Ring Ty pes (R)
[020-999] =  System  Speed Bi ns 1 020–1999,
for Off- Net Ringing
a
a. Ex pan ded  Spe ed...