Vodavi Triad 1/2/3 System Programming Manual

2-66 O n-Bo ard Re la y Prog ra mming
On-Board Relay  Programming
Pro g ram mi ng  S te ps
1. Press FLASH and  di al [14]. Button #1  is lit to indicate Relay  #1 is 
se le cte d. T he  fol lowi ng me ss age  di spl ays:
X = 1- 6
YYYYYYYYYYYY = Ext  Page Zone 1-2, LBC  Sta  XXX,  Ran S tart X,  CO Control  XX,  PFTU
2. Press the button that corresponds to the  desired  relay.  That button 
lights . E nter  one  of the  following s equences  on  the keypa d:
[1] +  [1 or 2] Firs t two E xternal Page  Zone...

Baud Rat e As si gnm ents 2 - 67
Baud Rate  Assign ments
Pro g ram mi ng  S te ps
Pre ss FLASH an d di al  [1 5].  The first  button is lit and ready for 
pr ogra mmi ng Por t  #1. T he  foll owi ng me ss age  di spl ays :
Des crip ti on
The  Tr ia d  1/ 2/ 3  Sys tem provides outputs  such a s S MDR or ICLID  to  the 
standa rd  RS-232  connectors on  the MPB or optional SIU Modu les.
Port  #1, #3, #4  Baud Rates
Pro g ram mi ng  S te ps
1 . Pr es s t he  de si re d PO RT #  fl ex  but ton (FLASH 15, Bu...

2-68 Net wo rking Tabl es
By default, Port  #1 (MPB RS-232C),  Port #3  (RS-232) and  Port #4  (RS-232)  
baud rates  are set for 9600.
Po r t # 2 B aud  R at e
Pro g ram mi ng  S te ps
Press the PORT #2 flex button (FLA SH 15 , Bu tton #2) to  ver i fy t he  bau d  
ra te of  the On-Boa rd  modem. T he  following m ess age displays :
Des crip ti on
PORT #2 -- On-Bo ard 2400  Baud  is standard on the Tr iad 3 System, but 
optiona l on Tr iad 1/ 2.  By default, the On-Board modem  baud  rate is set 
for...

Ne t wo r k i n g  Ta b l e s 2 - 69
Des crip ti on
The Networking Table  identifies the  system number (1-16); the CO group 
(0 -2 3);  t he r ang e of  st at ion  numbe r s (f rom  XXX X t o XX XX);  and  th e I P 
addr e ss.
TRU NK GRPSTATION
RANG E FRO MSTATIO N
RANGE TOIP AD DRESS
=1Q=2W=3E=4R
=5T=6Y=7U=8I
=9O=10 P=11 A=12 S
=13 D=14 F=15 G=16 H
=17 J=18 K=19 L=20 ;
PAGE UPPAGE DOW NSYSTEM NO
=21 Z=22 X=23 C=24 V
Ta b l e  2 - 8 :  N e t w o r k i n g  T a bl e s
Sys te m CO G r o u pStation Range...

2-70 Acces s Co des
Co n dit io n s
†Wi th  Fle xi ble  Num ber i ng e nabl ed /us ed,  th e c a ll  for wa rdi ng f eat ur e 
changes.
†Feature  access  codes ca nnot  conflict with  station  numbering.
†CO line numbe rs  are fixed and ca nnot be  chang ed othe r tha n the 
c urr ent  F LA SH  42  r e- ass ignm ent .
†The  VMI D di gi ts  ne ed  to  be  pr ogra mmed  se par at el y.
†The SMDR will output up  to 4-digit  numbers in  the station  field. If less 
than 4 digits are  selected in the...

Access  Code s 2 -71
Des crip ti on
Thi s  sect i on de scr ibe s  the  pr oced ure s a nd s te ps  nece ss ary  t o pr ogr am 
Access  codes.
DI S A Acc ess  Co de
Pro g ram mi ng  S te ps
1 . Pr es s t he  DI SA  ACC ES S CO DE  fl ex bu tt on (FLASH 20, Bu tton  #1). The  
following message displays:
2. Enter a valid number (000–999) on the dial pad for the DISA access 
code.
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The DISA  Access...

2-72 S tation  Mess age Detail Recording (SMDR)
D atabase Ad mi n  Pass word
Pro g ram mi ng  S te ps
1. Press the ADMIN PASSWORD flex button (FLASH 2 0, Bu tton #2). The  
following message displays:
2. Enter a valid number on the dial pad that corresponds with 
0000-9999.
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The password  used to enter  customer database programming  can be 
c ust omiz e d by  t he  prog ram mer . T hi s l et s  the...

Sta tion Mes sage  Detail Recording  (SMDR) 2 -73
4. After  all entries are  made, press HOLD to save the entry. A 
conf irmation  ton e is  hea rd.
Des crip ti on
The  Triad 1/2/3 Sys tem can p rov ide SMDR ou tput to the optional RS-232C  
connectors on  the MISU.  When S MD R is desired,  th e f ollowin g 
system-wide parameters determine how SMDR information is reported.
SMDR Enable / Disable
Pro g ram mi ng  S te ps
1. Press the ENABLE/DISABLE  flex button ( FLASH 21, Butto n #1 ). Thi s 
fea tur e...

2-74 S tation  Mess age Detail Recording (SMDR)
Des crip ti on
The sy stem  can b e s et to record a ll outgoing calls or only outgoing long 
di st ance  call s.  Long  Di st ance  cal ls  ar e  defi ne d as  be gi nning  wi th  a 1  or  0 , 
or  conta ining e ight  or  more d igits . Incoming ca lls a re  only recorde d if 
TYPE  is  se t  for  al l  cal ls.  By  defa ult ,  the  sy st em  re cords  l ong d ist ance  (L D) 
calls only .
Charac te r Print Ass ignme nt
Pro g ram mi ng  S te ps
1 . Pr es s...

We ekl y N ig ht Mo de  Schedul e 2 - 75
SMD R Po rt A s si gnmen ts
Pro g ram mi ng  S te ps
1 . Pr es s t he  P OR T  fl ex  but ton  (FLASH  21, Button  #5) to  de te rmi ne  
which port to use for SMDR information.
2. Enter a valid number for the  SMDR Port number:
[1]  = Port  #1 (MPB On-Board  RS -232C)
[3]  = Port  #3 (RS- 232C on  option al  SIU)
[4] =  Port # 4  (RS- 232C  on  optional S IU )
The LCD  displays  the current baud rate based on  which  Port number 
is  as si gned  to   th e S M DR...