Vodavi Starplus Automatic Voice Processing Technical Manual

STARPLUS@ AVP TECHNICAL MANUALMULTI-TASKING
3. Remove Disk 
# 7 and install the disk labeled 386 Files into
the A: drive.
4. Type: A:INSTALL C: then press [ENTER]. The system will
prompt:
The 
Starplus AVP multi-tasking system will now be copied to
drive C:
5. Press the [ENTER] key to continue or [CTRL + C] to abort.
The system will install the second set of Multi-Task files on the
disk. Upon completion of the installation the following will be dis-
played:Multi-Tasker Installation Complete.
At this...

MULTI-TASKINGSTARPLUS@ AVP TECHNICAL MANUAL
C. THE MULTI-TASK
SCREENWhen the Multi-Task screen appears, there will be four programs
(tasks) assigned to it. Two of the tasks will show as active in the
status portion of the screen. These tasks are the 
Runtime pro-
gram and the Dansr program. The screen will look like this:
u3.01
Swap Avail: ZlbEKtiax Task:633HDisk Space:103 neg
Ctrl-Shift-l for Task Controller
TasksstatusMemory Pri 
Clck BckGrnd dutoI1I I II
2. SPAVP llaintenanceNot Active45BK 24 Lower...

sTARPLUS@ AVP TECHNICAL MANUALMULTI-TASKING
lPriority (Pri) - This field indicates the importance of the
program as far as processor time is concerned.
The 
Runtime program should have a priority of 3 and all other pro-
grams should have a priority of 2. These values should not be
changed!
lClock (Clck) - This field allocates th,e amount of CPU
clock time dedicated to each program. There are 18 clock
ticks per second.
The 
Runtime program should have a value of 7, the Maintenance
and DOS Shell program...

MUL-l%T;ASKINGSTARPLUS@ AVP TECHNICAL MANUAL
DEACTIVATING PROGRAMS
As mentioned above, it is recommended that the DOS Shell and
the 
Starplus AVP Maintenance programs be deactivated when
they are not used.
,’1. To deactivate the DOS Shell type EXIT while you are at the
DOS prompt. You will be returned to the Task Controller
screen.E. MULTI-TASKING
PROGRAMMING2. To deactivate 
Starplus AVP Maintenance press [Fl 0] from
the maintenance main menu screen. You will be returned to
the Task Controller screen.....

STARPLUS@ AVP TECHNICAL MANUALMULTI-h&f@You may select one of these items and press the [ENTER] key.
The programming field for the item will appear.
I
MAINT sn700001u+3.lZd
ConfigurationmReportsUtilitiesIHouseKeepingi
2. SPAVP flaintenancePriority :  33. DOS ShellClock Ticks : 74. DfiNSRLower in Background: No5. Automatically Load : YesI
ESC-exitFB-deleteESC-exitI
Enter the descriptive name for this process.Verify that the following settings are on each item:
STARPLUS RUNTIME
lMemory = minimum 515K or...

MULTI-TASKINGSTARPLUS@ AVP TECHNICAL MANUAL
6. Press the [ESC] key when finished with all changes. Keep
pressing this key until you are at the Modules main menu
item.7. Press the 
[FlO] key to exit the Maintenance program.
At this point you must shut down the Multi-Tasker for the changes
to take effect. To shut down the Multi-Tasker all programs that are
Active must be shut down. Refer to the above section DEACTI-
VATING PROGRAMS.
8. Press the 
[SHFT]+[FlO] simultaneously at the Multi-Task
screen. A...

STARPLUS@ AVP TECHNICAL MANUALMULTI-TASKING
A. INSTALLATION OF
DANSR AND DCALLThe Dansr program is installed when you receive the 
StarplusAVP custom. It is located on the hard drive in its’ own directory,
the full path name is C:bDANSR. The Dansr program is also setup as a partition in the Multi-Task program and is set to automat-
ically load when the Multi-Tasker is started. If you ever upgrade/re-
place the hard drive the S/W installation procedure will
automatically install and set up the Dansr...

MULTI-TASKINGSTARPLUS@ AVP TECHNICAL MANUAL
After the call has been placed with 
Dcall, Dansr will answer the
call and the two modems will connect. At this point the calling
PC’s screen will show what is on the remote (VM) PC’s screen.
You may move through the Multi-Tasker as if you were on site.
The arrow keys will move the highlight bar, the [ENTER] key will
select a particular program, etc. Once the calling PC has control
of the VM PC, the following commands should be used in place of
[CTRL]+[SHFT] to...

STARPLUS @ AVP TECHNICAL MANUALVOICE BOARD SETTINGS
APPENDIX EVOICE BOARD SETTINGS
E.l
INTRODUCTIONThere are three jumpers-and a DIP switch that need to be set on
the voice board. The jumpers are labeled JP7, 
JPl, and JP5.
Each is located near the bottom of the board just above the bus
connector. The DIP switch, located above the bus connector, has
four toggle switches.
lJumper JP7 is used to identify the terminating voice board
in your 
Starplus AVP system. This jumper must only be in-
stalled on one...

VOICE BOARD SEl-l-INGSSTARPLUS @ AVP TECHNICAL MANUAL
as the first board in the system and will contain lines 1
through 4. The next lowest address is the second board in
the system and will contain lines 5 through 8. A basic 
Star-plus AVP system can contain up to 3 boards.
The basic rules for selecting memory addresses are as follows:
lDifferent Address For-Each Voice Board,- In multiple
board installations, you must use different addresses for
each board. If you do not, 
Starplus AVP will either not...