Vodavi Starplus 96ex Hybrid Key Telephone System Installation Manual

, 
sTAFiPLUS@ 96EX Key Telephone System 
. 
I= 
(9. 
r- 
MOUNTING PLATE 
--I 
HANDSh&TAlNER 
. 
@Jz2) 
“-3 
 
 
“4’7cRms 
Figure 500-l 4 SP 96EX Key Telephone Wall Mounting 
500-22 Issue 1, June 1991  

sTARPLUS@ 96EX 
Key Telephone System 
500.20 HEADSET INSTALLATION 
The Starplus 96EX Key Telephones have been de- 
signed to operate with industry standard electret mic 
compatible modular headset adapters and operator 
headsets. To modify a Starpius Key Telephone to 
support an external headset, plug the headset 
adapter cord into the vacant handset jack on the Key 
Telephone base. Plug the telephone handset cord 
into the headset adapter box where indicated by the 
headset manufacturer’s instructions....

sTARPLUS@ 96EX Key Telephone System 
RED 
COLORED 
C 
c 
RSM MODULE 
R 
S / 
3 d 
2 
2 C 
R Sl 
MOD 1 JACK 
EXT. PAGE VOICE 
+l MOD 2 JACK 
EXT. PAGE CONTROL 
MOD 3 JACK 
SIU MODULE 
7 
Mounting Holes 
Figure 500-M Application Board (APL) 
500-24 issue 1, June 1991  

4 CQNDUCTOR CORO & JACU 
MOO 1 - EXTERNAL PAGE VOICE 
CONNECTIONS 
PIN APL 
# CQLOR  
2 GN EPVT 
APL 0OARO EXIERNAL PAGING 
EQUIPMENT 
-D 
VOICE OUTPUT TO 
SPEAKERS 
 
EREAK 
CONTROL 
MAKE 
CONTROL CONTROL 
CONTACTS 
4 CONOUCTOR CORO 6 JACK 
MOD 2 - PAGING CONTROL CONTACTS 
6 CONDUCTOR CORD &JACK 
MOD 3 - RAN CONNECTION9 
P 
3 GN RANVT 
VOICE IN 
INPLIT FROM RECORDED 
4 
RO RANVR ANNOUNCEMENT DEVICE 
2 SK RANCTL 
MAKE 
1 START CONTROL TO 
5 n iw4cn CONTROL RAN DEVICE 
1 SL FSNSNS 
SENSE STOP CONTROL FROM...

snmPLus@ 96Ex Key Telephone System 
Basic 
KSU 
MOD 1 JAC 
MOD 2 JAC 
MOD 3 JAG APL MOD I JACK 
EXTERNAL PAGE OUTPUT CONNECTIONS 
PIN 1 - NOT USED 
PIN 2 - EPVT (VOICE) 
PIN 3 - EPVR (VOICE) 
PIN 4 - NOT USED 
APL MOD 2 JACK 
EXTERNAL PAGE CONTROL CONTACTS 
PIN I - EPMT (MAKE CONTACT) 
PIN 2 - EPBT (BREAK CONTACT) 
PIN 3 - EPBR (BREAK CONTACT) 
PIN 4 - EPMR (MAKE CONTACT) 
APL MOD 3 JACK 
RECORDED ANNOUNCEMENT (RAN) JACK 
PIN 1 - RAN SENSE (End of Message) 
PIN 2 - RAN CONTROL (Start Message) 
PIN 3 -...

‘ 
sTARPLUS@ 96EX 
Key Telephone System 
COB 
TIP MDF --- 
RING 
VOICE RING 
POWER FAILURE TRANSFER 
,--..------------..-.----.----..-. 
kJ-y$ 
: 
, 
:.----..-----.-.....--...--.-----, 
LBC Terminals 
on Basic KSU 
SIB 
CO RAN Connections 
--- 
--- 
Customer Provided 
Talk Battery 
24V DC 
RAN START 
RAN START 
GROUND START APPLICATIONS 
SLT RAN Connections 
VOICE RING 
LOOP START APPLICATIONS 
Figure 500-l 8 CO and SLT RAN Connections 
Issue 1, June 1991 
500-27  

G. Reinsert the .APL board in the BKSU 
H. Set switch seven on the CPB to the APL (ON) 
position. 
500.24 RS-232C CONNECTIONS 
One RS-232C type connector is provided and is 
located on the CPB board. There is an optional 
second RS-232C connector which can be installed 
on the APL board. The RS-232C connector on the 
CPB can be used for either Station Message Detail 
Recording (SMDR) or for on-line (Remote) database 
programming through the RS232C port using adata 
terminal. If the second RS-232C...

RSM Module Switch Settings 
Switch Settings 1 
Baud Rate 1 2 
I I 
2400 x x0 x 
4800 x x x0 
O=ON; X=OFF 
Equipment Needed: 
1 Phillips Screwdriver 
Two screws with washers are used to mount the RSM Module to the 
Applications Board (APL). 
Figure XXI-19 RSM Baud Rate Selection 
Issue 1, June 1991 500-29  

sTA!3PLUS@ 96EX Key Telephone System 
2 
6 
7 
20 / Transmit Data 
/ 
PRINTER 
TE%‘iAL 
Receive Data . 
RTS (Request to Send) 
CTS (Clear to Send) 
DSR (Data Set Ready) 
/ GND  
DTR (Data Terminal Ready) 
RS-232C PINOUT 
Data Communication Requirements are: 
A) Serial Port Compatible 
6) ASCII Code Compatible 
C 
D 8 Data Bits and 1 Stop Bit 
No Parity 
Figure 500-20 RS-232C Connections 
2 
5 
6 
7 
20 
sock30 Issue 1, June 1991  

sTARPLUS@ 96EX Key Telephone System 
Table 500-9 SMDR Printout 
The SMDR feature provides detailed records of all outgoing and/or incoming, long distance only or all calls 
exceeding 30 seconds. This feature is enabled or disabled in system programming. By default, SMDR is 
not enabled and is set to record long distance calls only. A printout format of 80 characters maximum or 29 
character maximum may be selected in system programming. The standard format is 69 characters on a 
single line. A 29...