Vodavi Discovery Ip Techical Guide

5-16 Discovery IP CONFIGURATION WIZARD
System ConfigurationAugust 1999
If YES was selected in Figure 25 (i.e., same number for all ports), the wizard asks for the 
number to correspond to all ports (Figure 26). If NO was answered in Figure 25, then a port 
number must be specified for each port. The screen in Figure 27 appears for each of the ports.
Figure 26: Port Number Assignment. When all ports have same number. 
Figure 27: Port Number Assignment. Unique number on each (same prompt on second, third,...

Discovery IP CONFIGURATION WIZARD 5-17
August 1999System Configuration
At the end of the configuration process, the wizard saves the selected options to respective 
configuration files, then displays the screen shown in Figure 28.
Figure 28: End of Configuration Process
In order for the new configuration options to take effect, the VOIP services must be restarted. 
The wizard asks whether the VOIP services should be restarted immediately (Figure 29).
Figure 29: ReStart Of VOIP Services For New Settings...

5-18 MANAGING Discovery IP CONFIGURATION SETTINGS
System ConfigurationAugust 1999
After completing the Wizard questions, the following screen prompts, “Would you like to quit 
now?” (refer to Figure 30). Selecting YES will result in the appearance of the System Status 
screen. Selecting NO will display a previous screen of the Wizard.
Figure 30: End of Configuration Wizard
MANAGING Discovery IP CONFIGURATION SETTINGS
The configuration interface consists of three steps. The first step includes general...

MANAGING Discovery IP CONFIGURATION SETTINGS 5-19
August 1999System Configuration
Figure 31: System Status Configuration Options Screen
The configuration interface is for displaying and making changes to the current configuration.
†To select an item on the main screen, move the cursor using the arrow keys, highlight the 
item and press ENTER
.
†To enter any changes, select the item in the main screen, then type or select the appropriate 
setting; press ENTER
.
†To go back to a previous screen, press TA...

5-20 MANAGING Discovery IP CONFIGURATION SETTINGS
System ConfigurationAugust 1999
Configuration Step 1 — General Discovery IP Setup
The settings you can edit in Configuration include the following (refer to Figure 32 and 33):
Figure 32: Discovery IP Configuration—Step 1
†Auto Start on Boot:  
Yes or No options. Yes indicates that software should run 
automatically upon startup/reboot of the Discovery IP machine.
†My Name:  
Enter full machine name (or domain name). Maximum length is 30 
characters, no...

MANAGING Discovery IP CONFIGURATION SETTINGS 5-21
August 1999System Configuration
Discovery IP unit is situated on the trunk side of a telco switch, this setting should be set 
to Default (by entering nothing). If there is a need to adjust the default voice volume 
through the Discovery IP (if situated on trunk side), try setting it to 0
 first.
ˆDiscovery IP is set to 0 from the factory. If the Discovery IP unit is initialized, or the 
software is reloaded, this setting should be changed back to 0
....

5-22 MANAGING Discovery IP CONFIGURATION SETTINGS
System ConfigurationAugust 1999
†Require Authorization:  
Available for use with NOMAP and Gatekeeper/Billing 
gateway types. With AMAS as gateway, this setting must be Ye s
. 
When used with 
NOMAP server type, setting Use Authentication to No
 will cause the 000.voc voice file 
(prompt for entering ID code) to be skipped so that only prompt is 043.voc message (Enter 
the number you’d like to dial). No authentication occurs whether the caller is prompted...

MANAGING Discovery IP CONFIGURATION SETTINGS 5-23
August 1999System Configuration
2. Continue with changes to the configuration by selecting Proceed at the bottom of the 
Step 1 Configuration screen. In this case the setup will continue onto the second step - 
Mapping Address specifications and interface-specific port configuration.
Configuration Step 2 — Mapping Address Specifications
The settings you can edit in this part of the Discovery IP Configuration include the following 
(refer to Figure 35):...

5-24 MANAGING Discovery IP CONFIGURATION SETTINGS
System ConfigurationAugust 1999
through the No Outbound setting. Each port also may have a dialing prefix associated 
with it to precede digits dialed for an outbound call; if port is FXS type, telephone 
number associated with that port should be entered into the Dial Prefix field.
ˆAll ports existing on the Discovery IP must be configured even if the port is inactive.
Completing Step 2 of Configuration
Once all settings have been entered (refer to...

MANAGING CONFIGURATION THROUGH THE WEB INTERFACE 5-25
August 1999System Configuration
Configuration Step 3 — Configuration Confirmation
Step 3 of Discovery IP configuration confirms the new configuration has been saved and 
instructs the user to restart the Discovery IP machine. At this point, you can quit out of the 
configuration program (type Q) or return to a previous step (refer to Figure 37).
Figure 37: Discovery IP New Configuration Confirmation
MANAGING CONFIGURATION THROUGH THE WEB 
INTERFACE
As...