ViewSonic Projector PJ359W User Manual

PJ359WViewSonic56

Troubleshooting
If an abnormal operation should occur, stop using the projector immediately. 
Troubleshooting
Otherwise if a problem occurs with the projector, the following checks and measures are recommended before requesting repair. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.
Related messages
When some message appears, check and cope with it according to the following table. Although...

ViewSonic57PJ359W

Troubleshooting
Regarding the indicator lamps
When operation of the LAMP, TEMP and POWER indicators differs from usual, 
check and cope with it according to the following table.
POWER 
indicator
LAMP 
indicator
TEMP 
indicatorDescription
Lighting
In Orange
Turned
off
Turned
offThe projector is in a standby state.Please refer to the section “Power on/off”.
Blinking
In Green
Turned
off
Turned
offThe projector is warming up.Please wait.
Lighting
In Green
Turned
off
Turned
offThe...

PJ359WViewSonic58

Troubleshooting
Regarding the indicator lamps (continued)
POWER 
indicator
LAMP 
indicator
TEMP 
indicatorDescription
Blinking
In Red
or
Lighting
In Red
Turned
off
Lighting
In Red
There is a possibility that the interior portion 
has become heated.Please turn the power off, and allow the projector to 
cool down at least 20 minutes. After the projector has 
sufficiently cooled down, please make confirmation of 
the following items, and then turn the power on again.
• Is there blockage...

ViewSonic59PJ359W

Troubleshooting
Phenomena that may be easy to be mistaken for machine defects
About the phenomenon confused with a machine defect, check and cope with it according to the following table.
PhenomenonCases not involving a machine defectReferencepage
Power does not come on.
The electrical power cord is not plugged in.
Correctly connect the power cord.10
The main power source has been interrupted during operation such as by a power outage (blackout), etc.
Please disconnect the power plug...

PJ359WViewSonic60

Phenomena that may be easy to be mistaken for machine defects (continued)
PhenomenonCases not involving a machine defectReferencepage
No pictures are displayed.(continued)
The brightness is adjusted to an extremely low level.
Adjust BRIGHTNESS to a higher level using the menu function or the remote control.
21, 23
The computer cannot detect the projector as a plug and play monitor.
Make sure that the computer can detect a plug and play monitor using another plug and play monitor.
9...

ViewSonic61PJ359W

Specifications
ItemSpecification
Product nameLiquid crystal projector
Liquid
Crystal
Panel
Panel size1.5cm (0.59 type)
Drive systemTFT active matrix
Pixels1,024,000 pixels (1280 horizontal x 800 vertical)
LensZoom lens F=1.7~1.9   f=19~23 mm
Lamp190W UHP
Audio output1 W x1
Power supplyAC100-120V/3.4A, AC220-240V/1.7A
Power consumption310 W
Temperature range5 ~ 35°C (Operating)
Size
274 (W) x 59 (H) x 205 (D) mm 
* Not including protruding parts. Please refer to the following 
figure....

PJ359WViewSonic62

Customer Support
For technical support or product service, see the table below or contact\
 your reseller.
Note : You will need the product serial number.
Country/RegionWeb SiteT=Telephone
F=FaxE-mail
Australia/New Zealandwww.viewsonic.com.auAUS=1800 880 818
NZ=0800 008 [email protected]
Canadawww.viewsonic.comT= 1-866-463-4775 
F= [email protected]
Europe/Middle East/Baltic countries/North Africawww.viewsoniceurope.comContact your reseller
Hong...

ViewSonic63PJ359W

Limited Warranty
VIEWSONIC® PROJECTOR
What the warranty covers: 
ViewSonic warrants its products to be free from defects in material and w\
orkmanship, under 
normal use, during the warranty period. If a product proves to be defect\
ive in material or 
workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace 
the product with a like product. Replacement product or parts may includ\
e remanufactured or 
refurbished parts or components. 
How long the...

PJ359WViewSonic64

Limitation of implied warranties: 
There are no warranties, express or implied, which extend beyond the des\
cription contained 
herein including the implied warranty of merchantability and fitness for a particular purpose. 
Exclusion of damages: 
ViewSonic’s liability is limited to the cost of repair or replacement of the produ\
ct. ViewSonic 
shall not be liable for: 
1.     Damage to other property caused by any defects in the product, damages based upon 
inconvenience, loss of use...

ViewSonic65PJ359W

Mexico Limited Warranty
VIEWSONIC® PROJECTOR
What the warranty covers:ViewSonic warrants its products to be free from defects in material and w\
orkmanship, under normal use, during the warranty period. If a product proves to be defective in \
material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a \
like product. Replacement product or parts may include remanufactured or refurbished p\
arts or components &...