ViewSonic Projector PJ359W User Manual

PJ359WViewSonic6

 C 
 B
A      16:10
B
CA     4:3

Setting up
Install the projector according to the environment and manner the projector will be 
used in.
On a horizontal surface
Suspended from the ceiling
• Keep a space of 30 cm or more 
between the sides of the projector 
and other objects such as walls.
• Consult with your dealer before 
a special installation such as 
suspending from a ceiling.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection...

ViewSonic7PJ359W

Setting up
WARNING  ►Place the projector in a stable horizontal position. If the 
projector falls or is knocked over it could cause injury and/or damage to the 
projector. Using a damaged projector could then result in fire and/or electric 
shock.
•  Do not place the projector on an unstable, slanted or vibrational surface such 
as a wobbly or inclined stand.
•   Do not place the projector on its side, front or rear position. 
•  
Consult with your dealer before a special installation...

PJ359WViewSonic8

K
COMPUTER IN1COMPUTER IN2USBAUDIO OUT
AUDIO INS-VIDEOVIDEO
AUDIOOUTAUDIOINUSB-AAUDIOOUTRGB OUT
VIDEO OUT
AUDIO OUTL           
R
S-VIDEO OUTAUDIO OUTL           R
AUDIO OUTL           
R
COMPONENTCR/PR    CB/PB     Y    
 
HDMI
HDMI OUTDVI OUT
RGB OUT

Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector. 
Make sure that all the devices are suitable to be connected with this product, and 
prepare the cables required to...

ViewSonic9PJ359W

Setting up
NOTE  • Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing,  and the resolution.-  Some signal may need an adapter to input this projector.
-   Some PCs have multiple screen display modes that may include some signals which 
are not supported by this projector. 
-   
Although the projector can...

PJ359WViewSonic0

Setting up
Connecting power supply
1. Put the connector of the power cord into 
the AC inlet of the projector.
2. Firmly plug the power cord’s plug into 
the outlet. In a couple of seconds after 
the power supply connection, the POWER 
indicator will light up in steady orange.
Please remember that when the AUTO ON function (38) activated, the 
connection of the power supply make the projector turn on.
WARNING  ►Please use extra caution when connecting the power cord, as...

ViewSonicPJ359W

Remote control
Putting batteries
Please set the batteries to the remote control before using it. If the remote control starts 
to malfunction, try to replace the batteries. If you will not use the remote control for long 
period, remove the batteries from the remote control and store them in a safe place.
1. Holding the hook part of the battery 
cover, remove it.
2. Align and insert the two AA batteries 
(HITACHI MAXELL, Part No.LR6 
or R6P) according to their plus and minus...

PJ359WViewSonic
Using as a simple PC mouse & keyboard
The enclosed remote control works as a simple mouse and keyboard of the PC, when the projector's USB port (B type) connects with the PC's mouse port via a mouse cable.
(1) PAGE UP key: Press the PAGE UP button.(2) PAGE DOWN key: Press the PAGE DOWN button.(3) Mouse left button: Press the ENTER button.(4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.(5) ESC key: Press the ESC button.(6) Mouse right button: Press the RESET...

ViewSonic13PJ359W
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESCENTERMENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUMEDOWNoONOFF9×FREEZE
Turning on the power
1. Make sure that the POWER indicator turns in steady orange and the lens cover is removed.
2. Press the STANDBY/ON button on the projector or the remote control. The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop...

PJ359WViewSonic14

Operating
Temporarily muting the sound
1. Press the MUTE button on the remote control.  A dialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the MUTE, VOLUME + or VOLUME - button. Even if you do not do anything, the dialog will automatically disappear \
after a few seconds.● When  is selected for the AUDIO item of the AUDIO menu (32),  the volume adjustment is disabled.
●   When
  is selected to VIDEO (NTSC), S-VIDEO (NTSC) or...

ViewSonic15PJ359W

Operating
Selecting an input signal (continued)
1. Press the VIDEO button on the remote control.  
Each time you press the button, the projector switches its input 
port as below. 
S-VIDEO  VIDEO 
● If the VIDEO button is pushed to switch from a signal from the 
COMPUTER IN1, COMPUTER IN2 or HDMI port, when TURN 
ON is selected for the AUTO SEARCH item in the OPTION 
menu (38), the projector will check the S-VIDEO port first. If no 
input is detected at the port, the projector will...