ViewSonic Projector Pj1158 User Manual

							
Projector Control
Projector	Control
Projector Control
The	tems	shown	n	the	table	below	can	be	per-
formed	usng	the	
[Projector Control] 	menu.
Select	an	tem	usng	the	up	and	down	arrow	keys	
on	the	PC.
Most	of	the	tems	have	a	submenu.
Refer	to	the	table	below	for	detals.
Controls	the	projector.
ItemDescription
Main
Power Turns	the	power	On/Off.
Input SourceSelects	the	nput	source.
Picture ModeSelects	the	Pcture	Mode	settng.
Blank On/OffTurns	Blank	On/Off.
MuteTurns	Mute	On/Off.
FreezeSelects	the	Freeze	settng.
MagnifyControls	the	Magnfy	settng.
Picture
BrightnessAdjusts	the	Brghtness	settng.
ContrastAdjusts	the	Contrast	settng.
GammaSelects	the	Gamma	settng.
Color TempSelects	the	Color	Temp	settng.
Color Adjusts	the	Color	settng.
TintAdjusts	the	Tnt	settng.
Sharpness Adjusts	the	Sharpness	settng.
Active IrisSelects	the	Actve	Irs	settng.
MyMemory Recall Recalls	the	MyMemory	data.
MyMemory SaveSaves	the	MyMemory	data.
76ViewSonic	 PJ1158 
						

							
Projector Control
Projector Control (Continued)
ItemDescription
Image
AspectSelects	the	Aspect	settng.
Over Scan Selects	the	Over	Scan	settng.
V PositionAdjusts	the	V	Poston.
H PositionAdjusts	the	H	Poston.
H PhaseAdjusts	the	H	Phase.
H SizeAdjusts	the	H	Sze.
Auto AdjustPerforms	Auto	Adjustment.
Input
Progressive Selects	the	progressve	settng.
Video NRSelects	the	Vdeo	NR	settng.
3D-YCSSelects the 3D-YCS setting.
Color Space Selects	the	Color	Space.
ComponentSelects	the	Component	termnal	settng.
C-Video FormatSelects	the	Vdeo	Format	settng.
S-Video FormatSelects the S-Video Format setting.
M1-DSelects the M1-D setting.
Frame Lock Turns	Frame	Lock	On/Off.
RGB in-1Selects	the	RGB1	nput	sgnal	type.
RGB in-2Selects	the	RGB2	nput	sgnal	type.
Setup
Aoto Keystone ExecutePerforms	the	Automatc	keystone	dstorton	correcton.
Keystone V Adjusts	the	Vertcal	Keystone	settng.
Keystone HAdjusts	the	Horzontal	Keystone	settng.
WhisperSelects	the	Fan	speed.	(Normal	or	Whsper)
MirrorSelects	the	Mrror	status.
77ViewSonic	 PJ1158 
						

							
Option
VolumeAdjusts	the	Volume	settng.
TrebleAdjusts	the	Treble	settng.
Bass Adjusts	the	Bass	settng.
SRS WOWSelects	the	SRS	WOW	settng.
SpeakerTurns	Speaker	On/Off.
Audio-RGB1Assigns the Audio-RGB1 input terminal.
Audio-RGB2Assigns the Audio-RGB2 input terminal.
Audio-M1-DAssigns the Audio-M1-D input terminal.
Audio-VideoAssigns the Audio-Video input terminal.
Audio-S-VideoAssigns the Audio-S-Video input terminal.
Audio-ComponentAssigns the Audio-Component input terminal.
Auto SearchTurns	the	Automatc	sgnal	search	functon	On/Off.
Auto KeystoneTurns	the	Automatc	keystone	dstorton	correcton	functon	On/Off.
Auto on Turns	the	Auto	on	functon	On/Off.
Auto offConfigures the timer to shut off the projector when no signal is de-tected.
My Button-1 Assgns	the	functons	for	the	MY
	BUTTON1	buttons	on	the	ncluded	
remote	control.
My Button-2 Assgns	the	functons	for	the	MY
	BUTTON2	buttons	on	the	ncluded	
remote	control.
Auto Adjust Enables/Dsables	Auto	Adjustment.
Remote Receiv. Front Enable/Dsable	Remote	Recev.	Front.
Remote Receiv. RearEnable/Dsable	Remote	Recev.	Rear.
Remote Receiv. TopEnable/Dsable	Remote	Recev.	 Top.
Remote Freq. NormalEnable/Dsable	Remote	Freq.	Normal.
Remote Freq. HighEnable/Dsable	Remote	Freq.	Hgh.
Projector Control
Projector Control (Continued)
ItemDescription
Audio
LanguageSelects	the	Language	for	the	OSD.
Menu Position VAdjusts	the	vertcal	Menu	Poston.
Menu Position HAdjusts	the	horzontal	Menu	Poston.
BlankSelects	the	Blank	mode.
StartupSelects	the	Startup	screen	mode.
MyScreen LockTurns	MyScreen	Lock	On/Off.
MessageTurns	the	Message	functon	On/Off.
Screen
78ViewSonic	 PJ1158 
						

							
Projector Control
Network Restart
Restarts	the	projector’s	network	connecton.
ItemDescription
RestartRestarts	the	projector’s	network	connecton	n	order	to	act-vate new configuration settings.
• Restarting requires you to re-log on in order to further control or con-
figure the projector via a web browser.
NOTE
Logoff
When	logoff	s	clcked,	the	logon	screen	s	dsplayed.
Projector Status
Displays and configures the current projector status.
ItemDescription
Error Status
Dsplays	the	current	error	status
Lamp TimeDsplays	the	usage	tme	for	the	current	lamp.
Filter TimeDisplays the usage time for the current filter.
Power StatusDsplays	the	current	power	status.
Input StatusDsplays	the	current	nput	sgnal	source.
Blank On/OffDsplays	the	Blank	On/Off	status.
MuteDsplays	the	current	Mute	On/Off	status.
FreezeDsplays	the	current	Freeze	On/Off	status.
79ViewSonic	 PJ1158 
						

							
Failure & Warning Alerts via E-mail
Failure & Warning Alerts via E-mail
The projector can automatically send an alert to specified e-mail addresses when 
the	projector	requres	mantenance	or	has	encountered	an	error.
• Up to five e-mail addresses can be specified.
• The projector may be not able to send e-mail if the projector suddenly loses 
power.
NOTE
Mail Settings
To use the projector’s e-mail function please configure the following items via a 
web	browser.
Example: If the IP address of the projector is set to 192.168.1.10:
• A Network Restart is required after the SMTP Port configuration set-
tngs	have	changed.	Clck	
[Network Restart] and configure the following items.
NOTE
	6)		 Clck	
[Mail Settings] and configure each item. Refer to the [Mail Settings]	
tem	n	 [Configuring	and	Controlling	the	Projector	via	a	Web	Browser] 	for	
further	nformaton.
	7)	Clck	the	
[Apply] 	button	to	save	the	settngs.
•	Clck	the	[Send Test Mail] 	button	n	[Mail Settings] to confirm that 
the e-mail settings are correct. The following mail will be delivered to the speci-
fied addresses.
NOTE
Subject	lne	 :	 Test	Mal	 
Text	 :	Send	 Test	Mal
		 Date	 
	 Tme	 
	 IP	Address	 
	 MAC	Address	 
	1)	Enter	
[https://192.168.1.10]
	nto	the	address	bar	of	the	web	browser.
	2)	Enter	the	 Admnstrator	ID	and	Password	and	clck	
[Logon].
	3)	Clck	
[Port Settings] 	on	the	man	menu.
	4)	Clck	the	
[Enable] 	check	box	to	open	the	SMTP 	Port.
	5)	Clck	the	
[Apply] 	button	to	save	the	settngs.
80ViewSonic	 PJ1158 
						

							
Failure & Warning Alerts via E-mail
 8)  Configure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings]	
on	the	man	menu.
 9)   Select and configure each alert item. Refer to 
[Alert Settings] 	n	[Configuring	
and Controlling the Projector via a Web Browser] 	for	further	nformaton.
10)	Clck	the	
[Apply] 	button	to	save	the	settngs.
Failure/Warning e-mails are formatted as follows:
Subject	lne	 :		 
Text		 :	
		 Date	 
	 Tme	 
	 IP	Address	 
	 MAC	Address	 
Mail Settings (Continued)
81ViewSonic	 PJ1158 
						

							
Projector management via SNMP
Projector	management	va	SNMP
When	SNMP	s	enabled,	the	projector	s	able	to	send	Falure/Warnng	 Alerts	to	a	
specified PC.
•	It	s	recommended	that	SNMP	functons	be	carred	out	by	a	network	
admnstrator.	
•	SNMP 	management	software	must	be	nstalled	on	the	computer	to	montor	
the	projector	va	SNMP.NOTE
SNMP settings
Configure the following items via a web browser to use SNMP.
Example: If the IP address of the projector is set to 192.168.1.10:
• A Network Restart is required after the SNMP Trap configuration set-
tngs	have	been	changed.	Clck	
[Network Restart] and configure the following 
tems.
NOTE
	5)	Clck	
[Security Settings] 	on	the	man	menu.
	6)	Clck	
[SNMP] 	and	set	the	Communty	Name	on	the	screen	that	s	dsplayed.
•	A 	Network	Restart	s	requred	after	the	Communty	Name	has	been	
changed.
•	Clck	
[Network Restart] and configure the following items.
NOTE
 7)   Configure the settings for Trap transmission of Failures/Warnings. Click 
[Alert 
Settings] on the main menu and select the Failure/Warning item to be config-
ured.
	8)		 Clck 	the 	
[Enable] 	check 	box 	to 	send 	out 	the 	SNMP 	trap 	for 	Fa lures/Warn ngs.	
Clear	the	
[Enable] 	check	box	when	SNMP 	trap	transmsson	s	not	requred.
	9)	Clck	the	
[Apply] 	button	to	save	the	settngs.
	1)	Enter	
[https://192.168.1.10]
	nto	the	address	bar	of	the	web	browser.
	2)	Enter	the	 Admnstrator	ID	and	Password	and	clck	
[Logon].
	3)	Clck	
[Port Settings] 	on	the	man	menu.
	4)		 Clck	the	
[Enable] 	check	box	to	open	the	SNMP 	Port.	
Set	the	IP 	address	to	send	the	SNMP 	Trap	to	when	a		Falure/Warnng	occurs.
82ViewSonic	 PJ1158 
						

							
Controlling the Projector via Scheduling
Controllng	the	Projector	va	Schedulng
The	projector	can	be	automatcally	controlled	va	schedulng.
•	You	can	schedule	the	followng	control	events:	Power	ON/OFF,	Input	
Source	and	 Transferred	Image	Dsplay.	
• There are 3 types of Scheduling, 1) daily 2) day of the week 3) specific date.
• The priority for scheduled events is as follows 1) specific date 2) day of the 
week	3)	daly.
• Up to five specific dates are available for scheduled events. Priority is given to 
those	wth	the	lower	numbers	when	more	than	one	event	has	been	scheduled	
for the same date and time (e.g., ‘Specific day No. 1’ has priority over ‘Specific 
day	No.	2’	and	so	on.	
•	Be	sure	to	set	the	date	and	tme	before	enablng	scheduled	events.
NOTE
83ViewSonic	 PJ1158 
						

							
Controlling the Projector via Scheduling
Date/Time Settings
The	Date/Tme	settng	can	be	adjusted	va	a	web	browser.
Example: If the IP address of the projector is set to 192.168.1.10:
•	A 	Network	Restart	s	requred	after	the	Daylght	Savngs	 Tme	or	
SNTP configuration settings have been changed.
•	 The	battery	for	the	bult	n	clock	may	be	dead	f	the	clock	loses	tme	even	
when	the	DATE	and	 TIME	have	been	set	correctly.	Replace	the	battery	by	fol
-
lowng	the	nstructons	on	replacng	the	battery.
•	 The	Internal	Clock’s	tme	may	not	reman	accurate.	Usng	SNTP 	s	recom
-
mended	to	mantan	accurate	tme.
NOTE
	1)			 Enter	[https://192.168.1.10] 	nto	the	address	bar	of	the	web	browser.	
Enter	the	 Admnstrator	ID	and	Password	and	clck	
[Logon].
	2)		 Clck	
[Date/Time Settings] on the main menu and configure each item. Refer 
to	the	
[Date/Time Settings] 	tem	n	[Configuring	and	Controlling	the	Pro-
jector via a Web Browser] 	for	further	nformaton.
	3)	Clck	the	
[Apply] 	button	to	save	the	settngs.
84ViewSonic	 PJ1158 
						

							
Controlling the Projector via Scheduling
Schedule Settings
Schedule settings can be configured from a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
There	are	three	types	of	schedulng.
 1) Daily: Perform the specified operation at a specified time every day.
 2)   Sunday ~ Saturday: Perform the specified operation at the specified time on a 
specified day of the week.
 3) Specific Date: Perform the specified operation on the specified date and time.
• In Standby mode the power indicator will flash green for approx. 3 
seconds	when	at	least	1	“Power	ON”	schedule	s	saved.
•	When	the	schedule	functon	s	used,	the	power	cord	must	be	connected	to	
the projector and the outlet and the power switch must be turned on, [ | ].  The 
schedule	functon	does	not	work	when	the	power	swtch	s	turned	off,	[
¡] or 
the	breaker	n	a	room	s	trpped.	 The	power	ndcator	wll	lghts	orange	or	green	
when	the	projector	gets	s	recevng	the	power.
NOTE
	1)	Enter	
[https://192.168.1.10] into the address bar of the web browser.
	2)	Enter	the	 Admnstrator	ID	and	Password	and	clck	
[Logon].
	3)		 Clck	
[Schedule Settings] 	on	the	man	menu	and	select	the	requred	schedule	
tem.
	4)	Clck	the	
[Enable] 	check	box	to	enable	schedulng.
 5) Enter the Date (Month/Day) for specific date scheduling.
	6)		Clck	
[Add] 	and	set	the	hour,	command	and	parameters	and	clck	[Add This 
Schedule] 	when	you	want	to	add	a	command.
	7)	Clck	the	
[Delete] 	button	when	you	want	to	delete	a	schedule.
	8)	Clck	the	
[Apply] 	button	to	save	the	settngs.
85ViewSonic	 PJ1158