ViewSonic Projector Pj1158 User Manual

							
Power on/off
Turning on the power
1.	Make sure that the power cord is firmly and cor-
rectly	connected	to	the	projector	and	the	outlet.
2.	Remove	the	lens	cover,	and	set	the	power	swtch	to	
the	ON	poston.		
The	power	ndcator	wll	lght	up	n	steady	orange.	 Then	
wat	several	seconds	because	the	buttons	may	not	func
-
ton	for	these	several	seconds.	
(1) When AUTO ON in OPTION menu is set to TURN ON	:The	lamp	wll	only	be	automatcally	turned	on	when	the	
Power	swtch	s	turned	on	after	the	power	was	turned	off	by	
Power	swtch	last	tme.	 Afterwards	the	POWER	ndcator	
wll	begn	blnkng	n	green.	When	the	power	s	completely	
on,	the	ndcator	wll	stop	blnkng	and	lght	n	green.
(2) When AUTO ON in the OPTION menu is set to TURN OFF : 
Please	see	step	3.
3.	Press	the	STANDBY/ON	button	on	the	projector	or	the	re-
mote	control.	
To	dsplay	the	pcture,	select	an	nput	sgnal	accordng	to	the	secton	
"Selecting an input signal".
Turning off  the power
1.	Press	the	STANDBY/ON	button	on	the	projector	or	the	remote	control.The message "Power off?" will appear on the screen for about 5 
seconds.
2.	Press	the	STANDBY/ON	button	on	the	projector	or	the	remote	
control	agan	whle	the	message	appears.	
The	projector	lamp	wll	go	off,	and	the	POWER	ndcator	wll	begn	
blnkng	n	orange.	
Then	the	POWER	ndcator	wll	stop	blnkng	and	lght	n	steady	
orange	when	the	lamp	coolng	s	complete.
3.	Make	sure	that	the	power	ndcator	lghts	n	steady	orange,	and	set	the	power	
swtch	to	the	OFF	poston.	 The	POWER	ndcator	wll	go	off.	 Attach	the	lens	cover.
Do	not	turn	the	projector	on	for	10	mnutes	or	more	after	turnng	t	off.	 Turnng	the	projector	
on	agan	too	soon	could	shorten	the	lfetme	of	some	consumable	parts	of	the	projector.
POWER
(Steady	orange)
POWER	(Blnkng	n	green)
POWER
(Steady	green)
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGBLASERINDICATOR
STANDBY/ON	button POWER	
ndcator
 Power off ?
WARNING  ►A
	strong	lght	s	emtted	when	the	projector’s	power	s	on.	Do	not	look	nto	the	lens	
of	the	projector	or	look	nsde	of	the	projector	through	any	of	the	projector’s	open ngs.
►Do	not	touch	around	the	lamp	cover	and	the	exhaust	vents	durng	use	or	just	after	use,	
snce	t	s	too	hot.
NOTE 		•	Turn	the 	power 	on/off 	n 	r ght 	order. 	Please 	power 	on 	the 	projector 	pr or 	to 	
the 	connected 	dev ces. 	Power 	off 	the 	projector 	later 	than 	the 	connected 	dev ces.
•	Use 	the 	shutdown 	sw tch 	only 	when 	the 	projector 	s 	not 	turned 	off 	by 	normal 	procedure.
Power	on/off
POWER
(Blnkng	n	orange)
POWER
(Steady	orange)
16ViewSonic	 PJ1158 
						

							
Operating
Operatng
Adjusting the volume
1.	Press	the	VOLUME	button	on	the	remote	control.	
A	d alog 	w ll	appear 	on	 the	screen 	to	 ad 	you	n 	adjust ng	the 	volume.
2.	Use the cursor buttons ▲/▼ to adjust the volume.
To	close	the	dalog	and	complete	the	operaton,	press	the	
VOLUME	button	agan.	Even	f	you	do	not	do	anythng,	the	
dalog	wll	automatcally	dsappear	after	a	few	seconds.
● When no audio port is selected for current picture input port, the volume adjust-
ment	s	dsable.	Please	see	the	 AUDIO	tem	of	AUDIO	menu.
Temporarily muting the sound
1.	Press	the	MUTE	button	on	the	remote	control.		
A	dalog	 wll	appear	 on	the	 screen	ndcat ng	that 	you	 have	 muted	 the	sound.	
To	restore	the	sound,	press	the	MUTE	or	VOLUME	button.	
Even	f	you	do	not	do	anythng,	the	dalog	wll	automatcally	
dsappear	after	a	few	seconds.
● As long as no audio input is selected for current picture input port, the sound is 
always	muted.	Please	see	the	 AUDIO	tem	of	AUDIO	menu.
Selecting an input signal
1.	Press	the	INPUT 	button	on	the	projector.		
Each	tme	you	press	the	button,	the	projector	swtches	ts	
nput	port	as	below.
													RGB	1					 					RGB	2					     M1-D 	
										VIDEO	 S-VIDEO 	COMPONENT
	(Y,	CB/RB,	CR/BR)
1.	Press	the	RGB	button	on	the	remote	control	to	select	an	
nput	port	for	the	RGB	sgnal.
	
Each	tme	you	press	the	button,	the	projector	swtches	ts	RGB	
nput	port	as	below.
									RGB	1		RGB	2	 M1-D 
● If the RGB button is pushed (when switching from VIDEO to RGB signals)  when	 TURN	ON	s	selected	for	the	 AUTO	SEARCH	tem	n	the	OPTION	menu	
the projector will check the RGB 1 port first. If no input is detected at the port, 
the	projector	wll	check	other	port	n	above	order.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
(contnued	on	next	page)
17ViewSonic	 PJ1158 
						

							
Operating
Searching an input signal
1.	Press	the	SEARCH	button	on	the	remote	control.
The	projector	wll	start	to	check	ts	nput	ports	n	order	to	
find any input signals.
When	an	nput	s	found,	the	projector	wll	stop	searchng	and	dsplay	the	mage.	
If	no	sgnal	s	found,	the	projector	wll	return	to	the	state	selected	before	the	
operaton.
RGB	1		RGB	2	 M1-D 	COMPONENT
	(Y,	CB/RB,	CR/BR)	 S-VIDEO 	VIDEO	
			
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
Selecting an input signal (continued)
1.	Press	the	VIDEO	button	on	the	remote	control	to	select	an	
nput	for	vdeo	sgnal.	
	
Each	tme	you	press	the	button,	the	projector	swtches	ts	
vdeo	nput	port	as	below.	
COMPONENT	(Y,	CB/RB,	CR/BR)	 S-VIDEO  	VIDEO		
			
● If the VIDEO button is pushed (when switching from RGB to VIDEO signals) 
when	 TURN	ON	s	selected	for	the	 AUTO	SEARCH	tem	n	the	OPTION	menu	
the	projector	wll	check	the	COMPONENT
	(Y,	CB/RB,	CR/BR) port first. If no input 
s	detected	at	the	port,	the	projector	wll	check	other	ports	n	above	order.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
Selecting an aspect ratio 
1.	Press	the	 ASPECT	button	on	the	remote	control.			
Each	tme	you	press	the	button,	the	projector	swtches	the	mode	for	aspect	
rato	n	turn.	
	For an RGB signal
NORMAL 	
	4:3		16:9		SMALL	
		
	For an M1-D signal
NORMAL 	
	4:3		16:9		14:9		SMALL	
		
	For a video signal, s-video signal or component video signal
4:3	
 	16:9		14:9		SMALL	
		
	For no signal 
4:3 (fixed)
● The NORMAL mode keeps the original aspect ratio of the signal.
● Performing the automatic adjustment initializes the aspect ratio setting.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
18ViewSonic	 PJ1158 
						

							
Adjusting the zoom and focus
1.	Use	the	zoom	rng	to	adjust	the	screen	sze.		
2.	Use	the	focus	rng	to	focus	the	pcture.
Operating
Focus	rng
Zoom	rng
Adjusting the lens shift
1.	Use	the	vertcal	lens	shft	dal	to	shft	
the	pcture	upward	or	downward.	
	
2.	Use	the	horzontal	lens	shft	dal	to	
shft	the	pcture	left	or	rght.
Using the automatic adjustment feature
1.	Press	the	 AUTO	button	on	the	remote	control.		
	For an RGB signal	
The	vertcal	poston,	the	horzontal	poston,	the	horzontal	
phase	and	the	horzontal	sze	wll	be	automatcally	adjusted.
	
And	the	aspect	rato	wll	be	automatcally	set	to	default.	Make	sure	that	the	
applcaton	wndow	s	set	to	ts	maxmum	sze	pror	to	attemptng	to	use	ths	
feature.	 A	dark	pcture	may	stll	be	ncorrectly	adjusted.	Use	a	brght	pcture	
when	adjustng.
	For an M1-D signal	
The	aspect	rato	wll	be	automatcally	set	to	default.
	For a video signal or s-video signal	
The	vdeo	format
  best	suted	for	the	respectve	nput	sgnal	wll	be	selected	
automatcally.
	
Ths	functon	s	avalable	only	when	the	 AUTO	s	selected	to	the	VIDEO	
FORMAT 	tem 	n 	INPUT 	menu. 	For 	a 	component 	v deo 	s gnal, 	the 	s gnal 	type	
is identified automatically independently of this function. 
	For a video signal, s-video signal or component video signal	
The 	vert cal 	pos t on, 	hor zontal 	pos t on 	and 	aspect 	rat o 	w ll 	be 	automat cally	
set	to	default.
	For a component video signal	
The	horzontal	phase	wll	be	automatcally	set	to	default.
● The automatic adjustment operation requires about 10 seconds. Also please  note	that	t	may	not	functon	correctly	wth	some	nput.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
2/5 
1/10 
1/10 
UP 
DOWN 
RIGHT 
Lens shift cover
LEFT NOTE 		•	When	the	vertcal	lens	shft	
s	adjusted,	t	s	recommended	to	shft	 the	pcture	upward.
Top
19ViewSonic	 PJ1158 
						

							
Adjusting the position
1.	Press	the	POSITION	button	on	the	remote	control.	
The	“POSITION”	ndcaton	wll	appear	on	the	screen.
2.	Use the cursor buttons ▲/▼/◄/► to adjust the picture posi-
ton.
When	you	want	to	reset	the	operaton,	press	the	RESET 	button	on	the	remote	
control	durng	the	operaton.
To	complete	ths	operaton,	press	the	POSITION	button	agan.	Even	f	you	do	
not	do	anythng,	the	dalog	wll	automatcally	dsappear	after	a	few	seconds.
● When this function is performed on a video signal, s-video signal or  component video 
signal, some image such as an extra-line may appear at outside of the pictur e.
● When this function is performed on a video signal, s-video signal, or component video signal 
of	525	(480)	or	625	(576),	the	range	of	ths	adjustment	depends	on	the	OVER	SCAN	n	IM
-
AGE	menu	settng.	It	s	not	possble	to	adjust	when	the	OVER	SCAN	s	set	to	10.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
Operating
Correcting the keystone distortions
1.	Press	the	KEYSTONE	button	on	the	
remote	control.	 A	dalog	wll	appear	on	the	
screen 	to 	a d 	you 	n 	correct ng 	the 	d stort on.
2.	Use 	the 	cursor 	buttons 	▲/▼	to 	select 	AUTO 	or	
MANUAL 	operaton,	and	press	the	button	
►	to	perform	the	followng.		
1)		AUTO	executes	automatc	vertcal	keystone	correcton.	
2)		Manual	dsplays	a	dalog	for	keystone	correcton.	
	
Use the cursor buttons ◄/► to select the direction to correct 
(	or	)	then	use	the	buttons ▲/▼ for adjustment.
To	close	the	dalog	and	complete	ths	operaton,	press	the	
KEYSTONE	button	agan.	Even	f	you	don’t	do	anythng,	
the	dalog	wll	automatcally	dsappear	after	a	few	seconds.
● The adjustable range of this function will vary among inputs. For some input,  ths	functon	may	not	work	well.
● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SET-
UP 	menu,	f	the	projector	screen	s	nclned	or	angled	downward,	ths	functon	
may	not	work	correctly.
● When the zoom adjustment is set to the TELE (telephoto focus), this function  may	be	excessve.	 Ths	functon	should	be	used	when	the	zoom	adjustment	s	
set to the full WIDE (wide-angle focus) whenever possible.
● When	the	projector	s	placed	on	the	level	(about	±3°),	ths	functon	may	not	work.
● When	the	projector	s	nclned	to	near	±30	degree	or	over,	ths	functon	may	not	
work	well.
● When	the	vertcal	lens	shft	s	not	set	fully	upward	(not	set	fully	 downward	for	the	
optional lens type FL-601 only), this function may not work well.
● When	the	horzontal	lens	shft	s	not	set	to	the	center,	ths	functon	may	not	work	well.
● Ths	functon	wll	be	unavalable	when	 Transton	Detector	s	on.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
-;5610#761:%76/#07#.




-;5610


20ViewSonic	 PJ1158 
						

							
Operating
Using the magnify feature
1.	Press	the	ON	button	of	MAGNIFY	on	the	remote	control.			
The	“MAGNIFY”	ndcaton	wll	appear	on	the	screen	(al
-
though	the	ndcaton	wll	dsappear	n	several	seconds	wth	no	
operaton),	and	the	projector	wll	go	nto	the	MAGNIFY 	mode.
2.	Use the cursor buttons ▲/▼ to adjust the zoom level. 
To	move	the	zoom	area,	press	the	POSITION	button	n	the	MAGNIFY 	mode,	
then use the cursor buttons ▲/▼/◄/► to move the area. And to finalize the 
zoom	area,	press	the	POSITION	button	agan.
To	ext	from	the	MAGNIFY	mode	and	restore	the	screen	to	normal,	press	the	
OFF	button	of	MAGNIFY 	on	the	remote	control.	
● The projector automatically exits from the MAGNIFY mode when the input sig-
nal	s	changed,	or	when	the	dsplay	condton	s	changed.	
● Although in the MAGNIFY mode, the keystone distortion condition may vary, it  wll	be	restored	when	the	projector	exts	from	the	MAGNIFY 	mode.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
Freezing the screen
1.	Press	the	FREEZE	button	on	the	remote	control.		
The	“FREEZE”	ndcaton	wll	appear	on	the	screen	(although	
the	ndcat on	wll	 not	appear 	when	 the	TURN	 ON	s	selected	 to	
the	MESSAGE	tem	of	SCREEN	menu),	and	the	projector	wll	
go	nto	the	FREEZE	mode.
To	 ext 	the	 FREEZE	 mode	and	restore	 the	screen	 to	normal, 	press 	the	 FREEZE	
button	agan.	
● The projector automatically exits from the FREEZE mode when the input signal  changes,	or	when	one	of	the	projector’s	buttons	or	the	remote	control	buttons	
of	STANDBY/ON,	SEARCH,	RGB,	VIDEO,	BLANK,	 AUTO,	ASPECT,	VOL
-
UME,	MUTE,	KEYSTONE,	POSITION,	MENU,	MAGNIFY 	and	MY	BUTTON	s	
pressed.
● If the projector continues projecting a still image for a long time, the LCD panel 
mght	possbly	be	burned	n.	Do	not	leave	the	projector	n	the	FREEZE	mode	
for	too	long.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
NOTE  • The zoom level can be finely adjusted. Closely watch the screen to 
find the level you want.
21ViewSonic	 PJ1158 
						

							
Operating
Temporarily blanking the screen
1.	Press	the	BLANK	button	on	the	remote	control.		
The	blank	screen	wll	be	dsplayed	nstead	of	the	screen	
of	nput	sgnal.	Please	refer	to	the	BLANK	tem	n	SCREEN	
menu.
To	ext	from	the	blank	screen	and	return	to	the	nput	sgnal	screen,	press	the		
BLANK	button	agan.	
● The projector automatically returns to the input signal screen when one of the  projector’s	buttons	or	the	remote	control	buttons	s	pressed	or	one	of	the	com
-
mands	(except	get	commands)	s	transmtted	to	the	control	port.
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGB
LASERINDICATOR
NOTE 		•	The	sound	s	not	connected	wth	the	blank	screen	functon.	If	
necessary, set the volume or mute first.
22ViewSonic	 PJ1158 
						

							
Operating
Using the menu function
Ths	projector	has	the	followng	menus:	PICTURE,	IMAGE,	INPUT,	SETUP,	AUDIO,	
SCREEN,	OPTION,	NETWORK,	and	EASY 	MENU.	EASY	MENU	conssts	of	functons	
often used, and the other menus are classified into each purpose. Each of these menus is 
operated	usng	the	same	methods.	 The	basc	operatons	of	these	menus	are	as	follows.
1.	Press	the	MENU	button	on	the	remote	control	or	one	of	
the	cursor	buttons	on	the	projector.			
The	 Advanced	MENU,	or	EASY 	MENU	that	has	prorty	just	
after	powered	on,	wll	appear.	
In the EASY MENU
2.	If	you	want	to	change	t	to	the	 Advanced	MENU,	select	the	"Go to Advanced Menu..."
3.	Use the cursor buttons ▲/▼ to select an item to operate.
4.	Use the cursor buttons◄/► to operate the item.
In the Advanced MENU
2.	Use the cursor buttons ▲/▼ to select a menu.	
If	you	want	to	change	t	to	the	EASY 	MENU,	select	the	
EASY 	MENU.
	Then press the cursor button ► on the projector or remote 
control,	or	the	ENTER	button	on	the	remote	control	to	select	
an	tem.	 The	dsplay	of	the	selected	menu	wll	be	actve.
3.	Use the cursor buttons ▲/▼ to select an item to operate.	Then	press	the	cursor	button	►	on	the	projector	or	remote	control,	or	the	ENTER	button	
on	the	remote	control	to	progress.	 The	operaton	menu	of	the	selected	tem 	wll	appear.
4.	Use the cursor buttons▲/▼ to operate the item.
● When	you	want	to	reset	the	operaton,	press	the	RESET 	button	on	the	remote	control	
durng	the	operaton.	Note	that	tems	whose	functons	are	performed	smultaneously	
wth	operaton	(ex.	LANGUAGE,	H	PHASE,	VOLUME	etc.)	cannot	be	reset.
	
● In	the	 Advanced	MENU,	when	you	want	to	return	to	the	prevous	dsplay,	press	the	cur-
sor	button	◄	on	the	projector	or	remote	control,	or	the	ESC	button	on	the	remote	con-trol.
5.	Press	the	MENU	button	on	the	remote	control	agan	to	close	the	menu	and	
complete	ths	operaton.	Even	f	you	do	not	do	anythng,	the	dalog	wll	auto-
matcally	dsappear	after	about	10	seconds.
● Some functions cannot be performed when a certain input port is selected, or  when	a	certan	nput	sgnal	s	dsplayed.
#5;/07=4)$?#52%6



:%76




)QVQ#FXCPEGF/GPW

014/#.
014/#.014/#.
J0).+5*
#761-;5610-;5610-;56102+%674/1&$4+)*6055%1064#56%1.146+065*#420559*+524/+4414456(+.646+/.#0)7#)


/07=4)$?
+/#)5672#7&+1
2+%674+0276
126+105%405*#42055
$4+)*60559×%1064#569×
%1.149×6+069×%1.146/2/+&)#//#&(#7.6
5.%6
06914-#5;/07#%6+8+4+567401((/;//14;5#8
RESET 	button
ENTER	button
MENU	button
Cursor	buttons
BLANKLASER
ASPECT
 ESC MENU RESET   POSITION AUTO    MAGNIFY MY BUTTON VOLUME ON 1    MUTE OFF 2 FREEZE KEYSTONE SEARCH 
PUSH ENTER
 PAGE UP  PAGE DOWN
 STANDBY/ON VIDEO RGBLASERINDICATOR
23ViewSonic	 PJ1158 
						

							
EASY Menu
EASY Menu
ItemDescription
ASPECTUsing the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu.
AUTO KEY-
STONE EXECUTE
Using the ► button executes the auto keystone function. See the AUTO KEYSTONE  EXECUTE item in SETUP menu.
KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion.See the KEYSTONE  item in SETUP menu.
KEYSTONE Using the ◄/► buttons corrects the horizontal keystone distortion.See the KEYSTONE  item in SETUP menu.
 PICTURE MODE
Using the ◄/► buttons switches the picture mode. 
The picture modes are combinations of GAMMA and COLOR TEMP settings. Choose a suitable mode according to the projected source.
               NORMAL ó CINEMA ó DYNAMIC 
  WHITEBOARD ó BOARD(GREEN) ó BOARD(BLACK)
COLOR TEMPGAMMA
NORMALMID DEFAULT#1 DEFAULT
CINEMALOW DEFAULT#2 DEFAULT
DYNAMICHIGH DEFAULT#3 DEFAULT
BOARD(BLACK)Hi-BRIGHT-1 DEFAULT#4 DEFAULT
Daylight ModeHi-BRIGHT-1 DEFAULT#3 DEFAULT
WHITEBOARDMID DEFAULT#5 DEFAULT
• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and COLOR TEMP items in PICTURE menu.• When this function is performed, a certain extra such as a line may appear.
From the EASY MENU, items shown in the table below can 
be performed. 
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control. Then perform it according to the 
following table. 
#5;/07=4)$?#52%6



:%76




)QVQ#FXCPEGF/GPW

014/#.
014/#.014/#.
J0).+5*
#761-;5610-;5610-;56102+%674/1&$4+)*6055%1064#56%1.146+065*#420559*+524/+4414456(+.646+/.#0)7#)


(continued on next page)
24ViewSonic  PJ1158 
						

							
EASY Menu
ItemDescription
BRIGHTNESSUsing the ◄/► buttons adjusts the brightness.
See	the	BRIGHTNESS	tem	n	PICTURE	menu.
CONTRASTUsing the ◄/► buttons adjusts the contrast.
See	the	CONTRAST	tem	n	PICTURE	menu.
COLORUsing the ◄/► buttons adjusts the strength of whole color.
See	the	COLOR	tem	n	PICTURE	menu.
TINTUsing the ◄/► buttons adjusts the tint.
See	the	TINT	tem	n	PICTURE	menu.
SHARPNESSUsing the ◄/► buttons adjusts the sharpness.
See	the	SHARPNESS	tem	n	PICTURE	menu.
WHISPERUsing the ◄/► buttons turns off/on the whisper mode.
See	the	WHISPER	tem	n	SETUP 	menu.
MIRRORUsing the ◄/► buttons switches the mode for mirror status.
See	the	MIRROR	tem	n	SETUP	menu.
RESETPerformng	ths	tem	resets	all	of	the	EASY
	MENU	tems	except	the	
FILTER	 TIME	and	LANGUAGE.A dialog is displayed for confirmation. Selecting the RESET using the ▲ button performs resetting.
FILTER TIME
Performing this item resets the filter time which counts usage time of the air filter.A dialog is displayed for confirmation. Selecting the RESET using the ▲ button performs resetting. 
See	the	FILTER	 TIME	tem	n	OPTION	menu.
LANGUAGEUsing the ◄/► buttons changes the display language. 
See	the	LANGUAGE	tem	n	SCREEN	menu.
Go toAdvanced Menu...
Select	“Go	to	Advanced	Menu…”	on	the	menu,	and	press	the	►	
or	ENTER	button	to	use	the	menu	of	PICTURE,	IMAGE,	INPUT,	
SETUP,	 AUDIO,	SCREEN,	OPTION	or	NETWORK.
EASY Menu (continued)
25ViewSonic	 PJ1158